User manual ACER H9500

[. . . ] · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this document or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGEMENT : · PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation. · Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. · VESA and SVGA are trademarks of the Video Electronics Standard Association. [. . . ] Do not touch the lens directly with your hand. Caring for the cabinet and remote control transmitter : Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth. ATTENTION · Make sure to turn off the power and unplug the power cord before caring for the unit. Please carefully read "Safety Instructions" in this manual, in order to care for your projector correctly. · Do not use cleaners or chemicals other than those listed above, including benzene and paint thinner. · Do not polish or wipe with hard objects. 31 LCD Projector CP-X870 USER'S MANUAL Thank you for purchasing this projector. Vol. 2 (Extended) WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this document or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGEMENT : · PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation. · Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. Use the table below as a guide for operation. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS : SELECT BNC VIDEO HDTV SYNC ON G P. POSIT RGB COMPONENT INPUT Menu Item Description Example : INPUT Menu (BNC) BNC Pin (R/CR/PR, G/Y, B/CB/PB, H, V) function selection: BNC (RGB) BNC (COMPONENT) (R) (G) (B) (H) (V) BNC (CR/PR) (Y) (CB/PB) ( - ) ( - ) (Pins for RGB) (Pins for COMPONENT) Selecting BNC (RGB) allows the 5 RGB2 pins (R/CR/PR, G/Y, B/CB/PB, H, V) to be used as RGB signal BNC input as-is. Selecting BNC (COMPONENT) allows the 3 leftmost RGB2 pins (R/C R/PR, G/Y, B/CB/PB) to be used as the COMPONENT VIDEO input CR/PR, Y, and CB/PB pins. Select Mode of Signal Type (for VIDEO/S-VIDEO): AUTO M-PAL NTSC N-PAL PAL SECAM NTSC4. 43 When AUTO is selected, the video/ S-video input function under ADJUST ( 5 ) are enabled, and is VIDEO executed simultaneously so that the optimum signal mode is selected from among the modes listed above. Use this function if the image becomes unstable with VIDEO/S-VIDEO. The image becomes irregular, or lacks color. ) · AUTO mode may not function correctly with a PAL60 signal and certain other signals. · The AUTO mode operation requires approximately 10 seconds. · For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below. HDTV Select HDTV Signal Mode: 1080i 1035i · If the selected HDTV mode is incompatible with the input signal, the picture may be distorted. On/Off SYNC ON G Mode: TURN ON TURN OFF Selecting TURN ON turns on the SYNC ON G mode. [. . . ] (3) The projector returns the response code `06H' to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (`04H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+`00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. [. . . ]