User manual ACER M200HDL

[. . . ] Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders. III Conventions The following conventions are used in this manual: SCREEN MESSAGES NOTE Denotes actual messages that appear on screen. [. . . ] Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. After setting the password, the computer sets the Supervisor Password parameter to "Set". If desired, you can enable the Password on boot parameter. When you are done, press u to save the changes and exit the BIOS Setup Utility. If the verification is OK, the screen will display as following. The password setting is complete after the user presses u. If the current password entered does not match the actual current password, the screen will show you the Setup Warning. 46 Chapter 2 If the new password and confirm new password strings do not match, the screen will display the following message. Chapter 2 47 Advanced The Advanced screen displays advanced settings in BIOS. InsydeH20 Setup Utility Information Main Security Advanced Boot Exit Rev. 3. 0 Item Specific Help Advanced CPU Control Platform Power Management IDE Configuration ACPI S1: ACPI S3: Auto wake on S5 Crestline PM Support POPUP Support POPDOWN Support DeepC4 Hard C4E [Enabled] [Enabled] [Disabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] These items control various CPU parameters. F1 Help Esc Exit Select Item Select Menu F5/F6 Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Advanced CPU Control Platform Power Management IDE Configuration ACPI S1 ACPI S3 Auto wake on S5 Description Option Sets the ACPI S1 sleep state. Enables the Auto wake on S5 by day of month or fixed time of every day, or disables this feature. Enables, disables Calistoga Enhanced Power Management mode. Enabled or Disabled Enabled or Disabled Disabled, By Every Day, or By Day of Month Crestline PM Support POPUP Support POPDOWN Support DeepC4 Hard C4E Enabled or Disabled Enabled or Disabled Enabled or Disabled Enabled or Disabled Enabled or Disabled Chapter 2 48 Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the diskette drive in module bay, the onboard hard disk drive, and the CD-ROM in module bay. InsydeH20 Setup Utility Information Main Security Advanced Boot Exit Rev. Unlock the battery lock (move the battery lock to the unlock position as shown). Slide the battery release latch then remove the battery. Chapter 3 57 Removing the HDD Module/Memory/Wireless LAN Card/Modem Card/ TV Tuner Card/System Fan/Thermal Modules/VGA Board/CPU/ Keyboard and the LCD Module Removing the HDD Module 1. Remove the two screws fastening the HDD cover. Detach the HDD cover from the main unit. 3. 4. Remove the screw fastening the HDD module. Pull the tab to remove the HDD module in the direction of the arrow. Removing the Memory 1. Remove the four screws holding the thermal cover. Detach the thermal cover from the main unit. Pop out the memory from the DIMM socket then remove it (If the notebook has two memory, then repeat this step). 58 Chapter 3 Removing the Wireless LAN Card/Modem Card and TV Tuner Card 1. Disconnect the three antennae from the wireless LAN card. Remove the two screws fastening the wireless LAN card. [. . . ] If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors. Chapter 4 87 Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. [. . . ]