User manual ACER PD113P

[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use by keys to select the desired item and adjust the settings key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. Press "Menu" on the Remote Control or press "Menu"on the Control Panel, the screen will return to the main menu. To exit OSD, press "Menu" on the Remote Control or press "Menu "on the Control Panel again. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu Sub Menu 17 . . . English User Controls Language Language Choose the multilingual OSD menu . Use the or key to select your prefered language. Press "Menu" on the Remote Control or press "Menu"on the Control Panel to finalize the selection. English. . . 18 User Controls Color (Computer / Video Mode) Display Mode There are many factory presets optimized for various types of images. User : Memorize user's settings. Brightness Adjust the brightness of the image. Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press the to increase the contrast. Color Temp. Adjust the color temperature. At higher temperature, the screen looks colder; at lower temperature, the screen looks warmer. White Segment Use the white Segment control to set the white peaking level of DMD 19 . . . English User Controls Color (Computer / Video Mode) chip. 0 stands for minimal segment, and 10 stands for maximum segment. If you prefer a stronger image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Degamma Effects the represent of dark scenery. With greater gamma value, dark scenery will look brighter. Saturation Adjusts a video image from black and white to fully saturated color. Press the to decrease the amount of color in the image. Press the to increase the amount of color in the image. NOTE Tint Adjusts the color balance of red and green. Press the to increase the amount of green in the image. Press the to increase the amount of red in the image. "Saturation" and"Tint" functions are not supported under computer mode. Color R Adjusts the red color. Color G Adjusts the green color. Color B Adjusts the blue color. [. . . ] Problem: LED lighting message Message Standby State (Input power cord) Lamp lighting Power on Power off (Cooling) Error (Lamp fail) Error (Thermal fail) Error (Fan lock fail) Error (Over Temp. ) Error (Lamp Breakdown) Power LED Blue Flashing Temp LED Lamp LED Flashing Flashing Flashing Flashing Flashing =>Light On =>Light Off English. . . 30 Appendices Problem: Message Reminders "Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!" will be shown about 10 seconds when lamp life is going to deplete. 31 . . . English Appendices Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message "Lamp is approaching the end of its useful life in full power operation. [. . . ]