User manual ACER PD116P

[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the problem persists, you should contact your local dealer or our service center. When the "TEMP" indicator flashs red for about 10 seconds, you will see a message "Fan fail. Please contact your local dealer or our service center. 12 Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. To exit OSD, press "Menu" again. 4 Confirm your selection of items. Four Directional Select Keys 4 Use to select items or make adjustments to your selection. 15 . . . English User Controls Using the Remote Control Power 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Empowering Key 4 Display the "Display Mode" submenu of the onscreen display Menu menu to select display mode from PC, Video, Theatre and User directly. 4 Press "Menu" to launch the on screen display menu. To exit OSD, press "Menu" again. Four Directional Selec t Keys 4 Use to select items or make adjustments to your selection. Laser Button 4 Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Zoom 4 Zoom in/out. Keystone + / - 4 Adjusts image distortion caused by tilting the projector (±16 degrees). Page Up (Computer mode only) 4 Use this button to page up. This function is only available Page Down (Computer mode only) when the projector is connected to a computer via an USB cable. 4 Use this button to page down. This function is only available Re-Sync when the projector is connected to a computer via an USB cable. 4 Automatically synchronizes the projector to the input source. Hide 4 Momentarily turns off the video. Press "Hide" to hide image, press again to restore display of the image. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video, DVI-D (Optional) and HDTV sources. Freeze 4 Press "Freeze" to pause the screen image. English . . . 16 User Controls On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel. 2. When OSD is displayed, use keys to select any item in the main menu. After selecting the desired main menu item, press to enter sub menu for feature setting. 3. Use settings by keys to select the desired item and adjust the key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel, the screen will return to the main menu. 6. To exit OSD, press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel again. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu Settings 17 . . . English User Controls Language (Computer / Video Mode) Language Choose the multilingual OSD menu . [. . . ] See page 25. Problem: Lamp burns out or makes a popping sound 4 When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp". See page 31. Problem: LED lighting message Message Standby State (Input power cord) Lamp lighting Power on Power off (Cooling) Error (Lamp fail) Error (Thermal fail) Error (Fan lock fail) Error (Over Temp. ) Error (Lamp Breakdown) Flashing Power LED Green Flashing Temp LED Lamp LED =>Light On =>Light Off English . . . [. . . ]