User manual ACER V196HQL

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondence concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. Acer Altos G530 Series Model Name : Part Number: Purchase Date: Place of Purchase: Acer and the Acer logo are registered trademarks of Acer Inc. [. . . ] This parameter is enabled by default and is not user-configurable. Enabled 98 4 BIOS setup Parameter USB 2. 0 Controller USB 2. 0 Controller Mode USB Mass Storage Device Configuration Description Enables the USB 2. 0 controller. Option Enabled Disabled HiSpeed FullSpeed Sets the transfer rate at HiSpeed (480 Mbps) or FullSpeed (12 MBps). Lets you specify the settings of the USB mass storage class devices. Press Enter to access the USB Mass Storage Device Configuration submenu. USB Mass Storage Device Configuration The USB Mass Storage Device Configuration submenu lets you specify settings for a USB mass storage device, such as a USB CD-ROM, CD-ROM/RW, DVD combo drive, and hard disk drives. Parameter USB Mass Storage Reset Delay Description Select the number of seconds POST waits for the USB mass storage device after the start unit command. Option 20 Sec 10 Sec 30 Sec 40 Sec Device #1 Emulation Type Type of USB mass storage device. When set to Auto, USB mass storage devices with less than 530 MB will be emulated as a floppy and the remaining drives are hard drives. The Forced FDD option can be used to force a formatted HDD to boot as a FDD. Auto Floppy Forced FDD Hard Disk CD-ROM 99 PCI Configuration The PCI Configuration submenu lets you specify settings that are related to the onboard controllers. Parameter Onboard Video Dual Monitor Video Description Enables or disables the onboard VGA controller. Select a graphic controller as a primary boot device. Note: This parameter will be grayed out when the Onboard Video is set to Disabled. Enables or disables the onboard NIC1 (Gigabit network interface controller). Enables or disables the onboard NIC1 ROM. Option Enabled Disabled Disabled Enabled Onboard NIC1 (Left) Onboard NIC1 ROM Enabled Disabled Enabled Disabled 100 4 BIOS setup Parameter Onboard NIC 2 (Right) Description Enables or disables the onboard NIC2 (10Base-T/ 100Base/ 1000 Base network interface controller). Enables or disables the onboard NIC2 ROM. Option Enabled Disabled Onboard NIC2 ROM Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enables or disables the onboard SCSI ontroller. Secures the system against unauthorized use. Once you set this password, you have to type it whenever you boot the system. User password is available only when a Supervisor password is set. Press Enter to change the Administrator password. Press Enter to change the User password. Option Not Installed Installed Not Installed Installed Set Admin Password Set User Password 111 Parameter User Access Level Description When set to Full Access, allows access to any field in the BIOS setup utility. When set to No Access, user is not allowed to access the BIOS setup utility. When set to View Only, allows access to the BIOS setup utility but fields cannot be changed. When set to Limited, allows access to Date and Time in the BIOS setup utility. Option Full Access No Access View Only Limited Clear User Password Clears the User password. Note: This parameter is grayed out when the Administrator password is not set. Enable or disables Boot Sector Virus Protection. Disabled Enabled Fixed Disk Boot Sector Protect Password On Boot NMI Control Select Enabled to activate security check during POST. [. . . ] (2) Press any key to reboot the server. RAID volume initialization After you create the RAID volume and saved the changes, the disk controller will automatically initialize the RAID volume. LSI Logic 1020A supports background initialization, there's no need to wait for the initialization to complete. Close the LSI Logic Configuration Utility after saving the changes. Using the MegaRAID configuration utility Turn on the system. When prompted, press Ctrl+M to enter the MegaRAID configuration utility. [. . . ]