User manual ACER V223PWL

[. . . ] To switch Screen modes: [PC] !' [ Ext. ] !' [ HDMI2] [ DVI] !' [ TV] !' [ Component] !' [ HDMI1] !' >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. [. . . ] Note · You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer. ) You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer. · 19 Connections · If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press 'SOURCE [ ]' button to have the monitor double-check the input signal source. Connecting to a Macintosh 1. Using the D-sub (Analog) connector on the video card. · Connect the signal cable to the D-SUB port on the back of your monitor. [PC] Note Turn on the monitor and Macintosh. Connecting to Other devices Note · · · This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. The DVI to HDMI cable, digital audio optic output cable, and RCA to stereo (for PC) cable are all sold separately. Contact a Service Center to purchase any products sold separately. Connecting EXT. (RGB) - It only applies to AV DEVICE that supports SCART. 20 Connections Note Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. When a Scart device is connected to your monitor, the Source automatically changes to Ext. Connecting TV Note You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer. 1. Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the monitor. 4. · · If no sound is emitted from the monitor, you need to use an amplifier. The user must adjust the frequency within that one minute. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported by the monitor. Maintenance and Cleaning 1. Clean with a soft cloth after disconnecting the power cord. 58 Troubleshooting · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repair of damages caused by him/her. Symptoms and Recommended Actions Note A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the SOURCE of the problem, and then contact a service center or your dealer. Check if the power cord and the video cables are properly connected to the computer. [. . . ] * Contact the video card manufacturer for details. Q: A: How can I set the Power Saving function?Windows XP: Set the resolution in the Control Panel !' Appearance and Themes !' Display !' Screen Saver. Set the function in the BIOS-SETUP of the computer. [. . . ]