User manual ACER V225HQL

[. . . ] (The locking device has to be purchased separately. ) For using a locking device, contact the place of purchase. Note · See Connecting the LCD Display for further information regarding cable connections. Remote Control Note · The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. 1. 33. REW STOP PLAY/PAUSE FF 1) ON / OFF Turns the LCD Display On/Off. 2) MAGICNET MagicNet Quick Launch Button. 3) MDC MDC Quick Launch Button. 4) LOCK Activates or deactivates all function keys on both the remote control and the LCD Display except for the Power and LOCK buttons. 5) MagicNet buttons Used for MagicNet. · Alphanumeric: Used to enter the Internet address. · DEL: Functions as the backspace. [. . . ] In general Video mode, selects FM Radio, and turns off the screen. In areas where the signal is weak, noise may occur during FM radio broadcasts. - This fuction does not work for this monitor. 23) P. SIZE Press to change the screen size. 24) SRS SRS 25) DUAL/MTS DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type MTS/S_Mode Mono Mono Mono Stereo Mono SAP Default Manual Change Mono FM Stereo Stereo SAP - This fuction does not work for this monitor. 26) PIP Every time you press the button, a PIP screen appears. 27) SOURCE Changes the source of the PIP window signal. 28) SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. 29) SIZE Switches the PIP Picture Size. 30) REW Rewind 31) STOP Stop 32) PLAY / PAUSE Play/Pause 33) FF Fast forward © 1995~2007 ACER. ALL Rights Reserved Select Language Main Page Model Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Connections Installing the Stand KIT Note · Only the supplied bolts should be used. Caution Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Installing the Semi Stand Left stand Right stand Caution Make sure to install the stand with the Caution label folded backwards. 1) To protect your product, a Cover Hole is included as an accessory. This protects the hole at the bottom of the monitor where the stand is inserted. If you install a wall mount kit for your monitor, please place the Cover Hole over it. 2) Insert it into the hole at the bottom of the monitor. Insert the screw provided with the Cover Hole into the marked place and fasten it firmly. Caution The resolution may differ for each product model. For information on the optimal resolution, refer to the user manual. Connecting the LCD Display Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note · Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. · Do not use benzene, thinner or other flammable substances, or a wet cloth. · We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note · A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. 1) 2) Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer. ) 3) 4) If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). [. . . ] Check if a special fluorescent or neon lamp is on in the vicinity. Q&A Question How can I change the frequency?Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details. ) How can I Adjusts the resolution? Windows XP: Set the resolution in the Control Panel Appearance and Themes Display Settings. [. . . ]