User manual ACER VERITON 7200D

[. . . ] Veriton 7200 series (Veriton 7200/Veriton 7200D) User's guide Copyright © 2001 Acer Incorporated All Rights Reserved. Veriton 7200 series (Veriton 7200/Veriton 7200D) User's guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. [. . . ] Adjust the keyboard height by flipping the folding stands located under the keyboard. Keep your lower arms parallel to the floor as you type. Your upper arms and shoulders should be relaxed. If you feel any shoulder or neck strain, stop for a while and check your posture. Position your keyboard in front of your monitor. Putting your keyboard beside your monitor will make you turn your head while you type which could add tension to your neck muscles that may later result in neck strain. · · Positioning your mouse · · · The mouse should be placed on the same surface as your keyboard so that you can reach it with ease. Adjust its position to allow enough space for movement without making you stretch or lean over. Do not rest your wrist on the table when moving the mouse. 27 Connecting peripherals Setting up your computer is easy. For the most part, you only have four things to connect: the USB keyboard, the USB mouse, the monitor, and the power cable. USB Keyboard Plug the keyboard cable into the USB port on the front or rear panel of your computer. (black port) located Note: If you are using a PS/2 keyboard, plug the keyboard cable into the PS/2 keyboard port panel of your computer. (purple port) located on the rear 28 3 Setting up your computer USB Mouse Plug the mouse cable into the USB port the front or rear panel of your computer. (black port) located on 29 Note: If you are using a PS/2 mouse, plug the mouse cable into the PS/2 mouse port your computer. (green port) located on the rear panel of Monitor To connect a monitor, simply plug the monitor cable into the monitor port located on the rear panel of your computer. Note: Refer to the monitor manual for additonal instructions and information. 30 3 Setting up your computer Power cable Caution: Before you proceed, check the voltage range in your area. Make sure that it matches your computer's voltage setting (refer to page 13 for the location of the voltage selector switch on the rear panel of your computer). If they don't match, change your computer's voltage setting according to your area's voltage range. Plug the power cable into the power cable socket located on the rear panel of your computer. Then plug the other end of the power cable into a power outlet. 31 Turning on your computer After connecting the necessary peripherals and plugging in the power cable, you are now ready to turn the computer on and get to work. Turn on all peripherals connected to your computer such as the monitor, printer, fax, speakers, etc. On the rear panel of your computer, set the voltage selector switch to the voltage range applicable to your area (a) then turn on the power switch (b). 32 3. 3 Setting up your computer On the front panel of your computer, press the power button. Important: Make sure that the power cable is properly plugged into an electrical outlet. If you are using a power strip or an AVR (Auto-Voltage Regulator), make sure that it is plugged in and turned on. 33 Turning off your computer To turn off your computer, click on the Start button, highlight Shut Down, select Shut down; then click on OK. You can then turn off all peripherals connected to your computer. If you cannot shut down your computer normally, press the power button for at least four seconds. Quickly pressing the button may put the computer in Suspend mode only. 34 3 Setting up your computer Connecting options Printer To connect a printer, plug the printer cable into the parallel port (burgundy port) located on the rear panel of your computer. Note: The printer shown below is for your reference only. [. . . ] However, if the diagnostic utility still reports a problem, then you may have to perform the recovery process to restore your system to its original default factory settings. · Note: For more information about recovering your system, refer to page 74. 78 Q: Nothing appears on the screen. 6Q&A A: Your computer's power management function automatically blanks the screen to save power. Just press any key to turn the display back on. If pressing a key does not work, you can restart your computer. If restarting your computer does not work, contact your dealer or the technical support center for assistance. Q: The printer does not work. [. . . ]