User manual ACER X1213P

[. . . ] 6 Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Panel Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connection Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Remote Control with Mouse Function & Laser Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the "Power/Standby" button to turn off the projector lamp. After pressing the "Power/Standby" button, you will see a message "Power off the lamp?" on the on-screen display. Press the "Power/Standby" button again to confirm. Other wise the message will disappear after 5 seconds. "Power/Standby" indicator flashes red for about 2 minutes. The projector will automatically shut itself down. If you want to turn on the projector, you must press the "Power/ Standby"button within 2 minutes of the start of the indicator flashing. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. When the "TEMP" indicator flashes red for about 10 seconds, you will see a message "Fan Fail" on the on-screen display. After 5 seconds, the "Power/Standby" indicator flashes green for about 2 minutes and the projector will automatically shut itself down. Please contact your local reseller or service center. to lighten the image. Brightness Adjusting the brightness of the image. 4 Press the 4 Press the Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. 4 Press the to decrease the contrast. Color Temperature Adjust the color temperature. The range is from "0" to "3". With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer. Zoom 4 Press the to Magnify an image up to a factor of 32 times on the projection screen. 4 Press the to Diminish the zoom in image. Keystone (Keystone Correction) Adjust image distortion caused by tilting projection. (±16 degrees) White Segment Use the white segment control to set the white peaking level of DMD chip. 0 stands for minimal peaking, and 10 stands for maximum peaking. If you prefera stronger image, adjust toward the minimum setting. For a smooth and more natural image, adjust toward the minimum setting. 18 English User Controls Video mode Language Management Image-I Image-II Audio Brightness Tint Contrast Sharpness Color White Segment Image-I (Video mode) Brightness Adjusting the brightness of the image. 4 Press the 4 Press the Contrast to darken the image. to lighten the image. The contrast controls the degree of difference between the lightest and darkest parts of the picture. [. . . ] If the projector is still not projecting the whole image, you will also need to change the monitor display you are using. Refer to the following steps. 27 English Appendices 4 . Click on the "Advanced Properties" button. Select the "Change" button under the "Monitor" tab . [. . . ]