User manual ACESONIC SP-280 DATASHEET

[. . . ] CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIO ELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORMESUR LE MATERIEL BROUILLEUR: APPAREILS NUMERIQUES , NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS. CAUTION To reduce the risk of electrical shocks, fire, etc: 1. Do not remove screws, screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. FCC INFORMATION (U. S. A. ) 1. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 22. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. Any mounting of the product should follow the manufacturer instructions, and should use a mounting accessory recommended by the manufacturer. Wet location marking Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personal. 3 Acesonic SP-280 Thank you for purchasing Acesonic's SP-280. Acesonic takes pride in providing our custmers with only the most advanced and highest quality karaoke products on the market. Please read trough this USER'S MANUAL before operation to ensure proper usage, and keep for future Table of Contents Warnings and Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Included Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. LOCK: to lock or unlock the buttons on the receiver. keep the distance between microphone and receiver IR launcher with-in 1 meter, then press the button on the microphone . If IR sync successes, the CH in the LCD screen will stop flashing and you can see the RF signal bar on the LCD screen. 5)IR launcher - submit matching signal to the receiver on the button of the microphone in order to make microphone match the same channel with this receiver. Rear panel descriptions 9 8 7 6 6) 12V AC power connection- Main power jack to power the system. 7) Channel A & B Mix unbalance audio output jack - Output jack that are used for connecting to amplifier, mixer or karaoke player. 8)Channel A balance audio output jack - Output jack that are used for connecting to amplifier, mixer or karaoke player. 9)Channel B balance audio output jack - Output jack that are used for connecting to amplifier, mixer or karaoke player. Will only send Channel B sound. 5 Microphone Descriptions Indicate Light Green=Working Yellow=Mute No light= power off Operation button 1 2 3 4 5 1)Cartridge module- This is where you would sing into. 2)Microphone body- The main frame of the microphone. 3)Operating indicator and 4)Switch buttonHold the switch button for 1 second to turn on the power. Light will turns green means microphone is now in working condition. [. . . ] O n the receiver, press MANUAL SCAN button twice in the roll to start auto channel scanning process. The whole auto scanning process will be finished around 90 seconds. However, you can stop auto scanning anytime by pressing STOP button. Receiver will select the best/cleanest channel from the channels just went thought. [. . . ]