User manual ACR ELECTRONICS NAUTICAST REV M

[. . . ] Please read this first! Warning: Although ACR strives for accuracy in all its publications; this material may contain errors or omissions, and is subject to change without prior notice. ACR shall not be made liable for any specific, indirect, incidental or consequential damages as a result of its use. ACR components may only be used in safety of life devices or systems, with the express written approval of ACR, as the failure of such components could cause the failure of the ACR device or system. If these fail, it is reasonable to assume that the safety of the user or other persons may be endangered. 2 Y1-03-0203 Rev. [. . . ] ++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | | <-Exit Dynamic Keys: User Password Input (Access Denied) [M8] [Exit] Return to Vessel Listing 48 Y1-03-0203 Rev. M a) Change User Password (for initial NAUTICASTTM Operation) It is strongly recommended to change the default User Password upon initial NAUTICASTTM operation. A minimum of 6, a maximum of 8 characters are allowed. Should the new password include numbers, use the shift key to generate them. N 1o19' E 0o12' |1>0. 10|2>1. 30|3>1. 80nm |---------------------------------| 5. | | -----| | Displ| ---------------------------------------NUM|Select->| | |<-Back N 1o33' E 0o27' |1>0. 10|2>1. 30| * 1A1L ********* Change User Password ********* Enter new password: Repeat new password: ***** ***** {Length: 6. . 8 characters} ---------------------------------------| Enter | | | Back Dynamic Keys: Initial User Password Setting [M5] [Enter] Confirm User Password Input [M8] [Back] Return to Menu Configuration Y1-03-0203 Rev. M 49 This screen appears if the new User Passwords are mismatched - i. e. the New User Password and the Repeated New User Password are not identical. In this case, it is possible to re-input both the New and Repeated User Passwords again. [Exit] takes the user back to the User Password Input Screen. N 1o19' E 0o13' |1>0. 10|2>1. 30|3>1. 80nm ---------------------------------------- ++++++++++++++++++++++++++++++++++++++++ Passwords mismatched!++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | |<-Exit Dynamic Keys: User Password Input (Password Mismatched) [M8] [Exit] Return to Password Input Screen The new User Password configuration has been saved. N 1o33' E 0o27' |1>0. 10|2>1. 30| * 1A1L ---------------------------------------- ++++++++++++++++++++++++++++++++++++++++ Data saved. ++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | | <-Exit 50 Y1-03-0203 Rev. M b) Region Settings A Region is a defined area, with specific VHF parameters, which are sent out by Vessel Traffic Service Stations (VTS), and received via Digital Selective Calling (DSC) or AIS. The screen shows a list of Regions, and their input sources. When the vessel enters into one of the pre-defined Regions, the NAUTICASTTM automatically switches to the relevant Region Setting. If a Region Number is vacant, then the relevant Region Name Slot is currently unoccupied. Tip: For fast Region Selection, press the Region Number on the keyboard and the selected region is immediately displayed. N 1o18' E 0o12' |1>0. 10|2>1. 30|3>1. 80nm *********** Region Settings ************ . . Name. . . . Valid. . . Source. . . . . . . DaysOld. . 1>Region 1 OK A:AddrChM 2 06:21:59 2>Region 2 OK B:BcastChM 37 09:36:14 3>Region 3 4>Region 4 OK ?N/A N/A 5>Region 5 OK M:OpManual 23 11:02:40 6>Region 6 OK C:AIS_ChAs 10 12:39:17 7>Region 7 8>Region 8 OK D:DSC_Ch70 27 05:56:34 9>Region 9 OK C:AIS_ChAs 9 17:08:46 In use:Region 6 ---------------------------------------NUM| Select->| New | |<-Back Dynamic Keys: Region Settings [M5] [M6] [Select] [New] Confirm Region Number Selection Create New Region [M8] [Back] Return to Menu Configuration Overview of Region Settings Name Valid Source Region Number OK A:AddrChM Number of pre-defined Region Status of Region Setting - OK: Stored and Valid A: Addressed Channel Management (Msge. 22) Source: VTS via AIS B: Broadcast Channel Management (Msge. 22) Source: VTS via AIS C: AIS Channel Assignment Sentence Source: Manual ECDIS Input D: Channel 70 Telecommand Source: Digital Selective Calling M: Operator Manual Input Source: Via Display Days, hours, minutes, seconds (dd hh:mm:ss) Region Setting of vessel current operation B:BcastChM C:AIS_ChAs D:DSC_Ch70 M:OpManual DaysOld In use Period of time Region Setting is stored Region 6 Y1-03-0203 Rev. M 51 Creating a New Region Parameters for setting up a new Region can be entered and saved here. N 1o19' E 0o12' |1>0. 10|2>1. 30|3>1. 80nm ********** Create New Region *********** NE LAT(1):N 0o 0. 0000' +----------1 NE LON(1):E 0o 0. 0000' | +------+ | o SW LAT(2):N 0o 0. 0000' || || SW LON(2):E 0 0. 0000' >|3|< || TrZone(3): 5nm | +------+ | ChannAIS1:2087 2----------+ BandwAIS1: Default ChannAIS2:2088 BandwAIS2: Default Tx/RxMode: TxA/TxB, RxA/RxB VHF Power: High ---------------------------------------| Save | | | Back Dynamic Keys: Initial User Password Setting [M5] [Save] Confirm Region Data Input [M8] [Back] Return to Region Listing Inputting Region Settings: Mode of Latitude and Longitude Input: Example: 44 Degrees, 13. 1234 minutes, North Input Format: N 44-13. 1234 Input Modes for New Regions Data Field NE LAT(1) Field Description Latitude N/E corner Input Modus Manual Input Manual Input Manual Input Manual Input <Selection> Manual Input <Selection> Manual Input <Selection> <Selection> <Selection> Additional Information Degrees and minutes Degrees and minutes Degrees and minutes Degrees and minutes Nautical Miles Channel Number Default Setting as defined by the channel number Channel Number Default Setting as defined by the channel number Tx : Transmitting Mode Rx: Receiving Mode Low = 2 Watt (Default for Ports) High = 12, 5 Watt (Default for High Sea Regions) NE LON(1) Longitude of N/E corner SW LAT(2) Latitude of S/W corner SW LON(2) Longitude of S/W corner TrZone(3) Transitional Zone Size Bandwidth for Primary AIS Channel Bandwidth for Secondary AIS Channel ChannAIS1 Primary AIS Channel BandwAIS1 ChannAIS2 Secondary AIS Channel BandwAIS2 Tx/RxMode Channel Modes VHF Power VHF Power Settings 52 Y1-03-0203 Rev. M c) Alarm Settings This screen allows the user to enable or disable the generation and display of Alarms. [. . . ] 78, 20359 Hamburg, Germany Inland AIS Type Approval Certificate No: R - 4 - 203 Issued by: Fachstelle der WSV für Verkehrstechniken Weinbergstraße 11-13, 56070 Koblenz, Germany IMO MSC. 74(69) Annex 3 ITU-R M. 1371-3 (Class A) IALA Technical Clarifications of Rec. 1. 3) ITU-R M. 825-3 ITU-R M1084-3 IEC 61993-2 (2001) IEC 61162-1 (2000), -2 (1998) IEC 60945 (1996) IEC 61108-1 (1996) Technical Specification for Vessel Tracking and Tracing Systems for Inland Waterways (Ed. 1. 01 dated 10. 10. 2007) Test Standard for Inland AIS, (Edition 1. 0 dated 31. 5. 2007) 2009-08 ACR Electronics Inc. , 5757 Ravenswood Road, Fort Lauderdale, Florida, 33312 USA ACR Electronics Europe GmbH Handelskai 388 / Top 632 A-1020 Vienna, Austria Vienna, 2009-07-22 Zertifikate der benannten Stelle: Certificates from the notified Body / Certificats des Organismes Notifiés Spezifizierte Standards: Specified Standard(s) / Standard(s) Spécifié(s) Dokumentennummer: Document number / Num. du document Hersteller: Manufacturer / Fabricant Anschrift EU-Vertretung: Address EU-Representative / Adresse du Représentant pour l'UE Ort, Datum: place, date / Lieu, Date Unterschrift: Signature / Signature Andreas Lesch Managing Director Diese Erklärung bescheinigt die Übereinstimmung mit den genannten Richtlinien, ist jedoch keine Zusicherung von Eigenschaften. [. . . ]