User manual ACR ELECTRONICS RCL-100 SEARCHLIGHT

[. . . ] Product Support Manual RCL-100DTM Remote Control Searchlight Master Controller Point Pad Y1-03-0138 Rev. 5757 Ravenswood Road Fort Lauderdale, Fl 33312 Tel : +1(954) 981-3333 Fax: +1 (954) 983-5087 www. acrelectronics. com Email: Info@acrelectronics. com RCL-100D TABLE OF CONTENTS SECTION 1. 0 2. 0 3. 0 4. 0 5. 0 6. 0 7. 0 8. 0 9. 0 10. 0 TITLE Forward General Searchlight Remote Control System URP-102 Point PadTM URC-102 Master Controller RCL-100D Specifications Bulb Replacement RCL-100D Searchlight Components Remote Control System Components PAGE 1 2 2 2 3 11 15 17 17 18 FIGURES Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 TITLE Remote Control Searchlight System Point PadTM Connection Block Diagram URP-102 Point PadTM Functions URP-102 Point PadTM Surface Mount Case URP-102 Point PadTM Flush Mount Case URP-102 Point PadTM Surface Mount Case w/Gasket and Flush Mount Case with Gasket URC-102 Master Controller Wiring Diagram URC-102 Master Controller Searchlight User Replaceable Parts List PAGE 1 4 5 6 7 8 11 12 14 i Y1-03-0138 Rev. K RCL-100D, 12/24V REMOTE CONTROL SEARCHLIGHT SYSTEM FIGURE 1: REMOTE CONTROL SEARCHLIGHT SYSTEM 1. 0 FORWARD Congratulations and thank you for purchasing the ACR RCL-100D Searchlight. The combination of computer aided design, high quality raw materials, and quality-controlled manufacturing produce a superior product. [. . . ] K URP-102 Point Pad Functions · · · · · · · Press the ON/OFF button to turn the lights ON or OFF. Press the SPEED button to toggle between High and Low rotation speeds. Press the Right or Left Arrows to rotate the Searchlight in that direction. Press the Up or Down Arrows to raise or lower the Searchlight-beam. To activate the XRCiZ feature, press and hold the ON/OFF button for greater than 5 seconds. The Green LED indicates XRCiZ feature is enabled. To deactivate the XRCiZ feature, Press and hold the ON/OFF button for greater than 5 seconds. The Red LED indicates XRCiZ feature is disabled. An LED blinking Red / Green indicates that the XRCiZ feature is now "exercising" the Searchlight. NOTE: XRCiZ Feature is only available when paired with a URC-102 Master Controller. FIGURE 3: URP-102 POINT PADTM FUNCTIONS 5 Y1-03-0138 Rev. K FIGURE 4: URP-102 POINT PADTM SURFACE MOUNT CASE 6 Y1-03-0138 Rev. J FIGURE 5: URP-102 POINT PADTM FLUSH MOUNT CASE 7 Y1-03-0138 Rev. J FIGURE 6: URP-102 POINT PADTM Surface Mount Case with gasket and Flush Mount Case with gasket 8 Y1-03-0138 Rev. J 6. 0 URC-102 MASTER CONTROLLER Mounting The Master Controller can be mounted in any position near the Searchlight that is protected from the weather. Check in advance that the coax cable from the Point PadTM and the wiring harness from the Searchlight can be routed to this location. Mount the Master controller with the wires and coax facing down. Use an appropriate fastener for your mounting location. Use a sealant in fastener holes to prevent moisture intrusion. General Wiring Scheme The RCL-100 has a unique wiring scheme. Special attention must be paid to the following chart. The Master Controller is supplied with an in-line fuseholder on the Orange power lead. Use only 15 amp fuses in this fuseholder. [. . . ] While enabled, The XRCiZ feature can be started outside of its 30-day cycle by pressing and holding the Speed button on the Point PadTM for greater than 5 seconds. While the XRCiZ feature is operating the Searchlight, pressing any Point PadTM button will stop the current cycle and leave the Searchlight to follow any additional commands. To deactivate the XRCiZ feature, press and hold the Point PadTM ON/OFF button for greater than 5 seconds. K 8. 0 BULB REPLACEMENT Two 55W, quartz-halogen bulbs are provided with your RCL-100D. [. . . ]