User manual ACR ELECTRONICS RCL-75 SEARCHLIGHT

[. . . ] 1946 Remote Control Searchlight System ACR Electronics, Inc. 5757 Ravenswood Road Fort Lauderdale, Fl 33312 +1(954) 981-3333 · Fax +1 (954) 983-5087 www. acrelectronics. com Email: Info@acrelectronics. com A Chelton Group company TABLE OF CONTENTS 1. 0 2. 0 3. 0 4. 0 5. 0 6. 0 7. 0 8. 0 9. 0 10. 0 11. 0 FORWARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SEARCHLIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNPACKING THE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CARE AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BULB REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SPECIFICATIONS and WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ACCESSORIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TEMPLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 i Y1-03-0158 Rev. D 1. 0 FORWARD Congratulations and thank you for purchasing the ACR RCL-75 Searchlight. The combination of computer aided design; high quality raw materials and quality-controlled manufacturing produce a superior product. [. . . ] Flush mount and Surface mount. (see Figures 6 & 7) Both mounting options require access to the backside of the mounting location. (see Templates ­ Y1-03-0158-1) Make sure there are no obstructions behind the area where the switch is to be located. bulkheads, wires, plumbing, hardware. ) Check in advance to verify the wiring harness can be routed to this location. 5. 3. 1 Surface Preparation for Remote Control Point PadTM Make sure area is clean and dry. Verify that drill hole will not impact or harm other items (wires, plumbing, hardware bulkhead). 5. 4 Mounting the Light Remove deck mounting plate from light base (4 Allen bolts). Locate the mounting plate on the spot that you want your light. Rotate the plate so that the arrows are pointing forward and the length of the arrow is aligned parallel to the keel. Mark the 4 mounting holes, starting with the one between the 2 arrows. Mounting holes are in 90° increments. (See template Y1-03-0158-1) 5 Y1-03-0158 Rev. D FIGURE 4 5. 4. 1 Surface Preparation for light Make sure surface is clean and dry. Verify that drill holes will not impact or harm other items (wires, plumbing, hardware or bulkheads). Can the backside of mounting surface be reached to install nuts and washers?Note: If the mounting surface is not flat, a special shapeable plate can be purchased, (P/N 9427), to adapt the light base to the surface. This plate can also be used to raise the light 1" if desired. (see Figure 4) Drill 4 mounting holes (1/4") and a centered cable clearance hole (3/4"). Put the mounting gasket on the deck mount (or shaped plate, if used). Use caulk or bedding compound to seal bolt and wire holes before deck mount is attached to deck. The plates are keyed to each other and to the light, be sure the arrows are pointing in the correct direction. (the light will rotate 180° either way from the arrows). Use marine grade 316 stainless steel bolts, nuts, and lock washers to fasten the plate(s) to the mounting surface. [. . . ] (see Figure 11) 6) At the point where the grey bulb wire passes through the partition wall, remove the sealant with a razor, screwdriver or snips. 21) The short wire of the right bulb and the long wire of the left bulb are joined together and inserted into the upper right side hole of the terminal block and screw tightened securely. Gather wires together and install new cable ties. (see Figure 19) 22) Replace the top cover carefully, making sure the partition is seated in its proper groove and the screw holes at the front match the metal braces. [. . . ]