Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ACT ACTENTRY V-IP. We hope that this ACT ACTENTRY V-IP user guide will be useful to you.
Lastmanuals help download the user guide ACT ACTENTRY V-IP.
You may also download the following manuals related to this product:
ACT ACTENTRY V-IP DATASHEET (195 ko)
Manual abstract: user guide ACT ACTENTRY V-IP
Detailed instructions for use are in the User's Guide.
[. . . ] ACTentry V-IP Operating & Installation Instructions
18-00068
This manual refers to ACTentry V-IP, a TCP/IP based door videophone system. reserve the right to change the contents of this manual and the system it applies to without prior notice. While every effort has been taken by ACT to ensure the accuracy of the information contained within this document, ACT assumes no responsibility for any errors or omissions. No liability is assumed for damages resulting from the use of information contained within this document.
Access Control Technology Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. [. . . ] (A fixed IP address may also be assigned, see section 5. 0). The LED's on the PCB indicate the status of the connection to the network. When both LEDs flash momentarily every couple of seconds, the unit is powered but not connected to the network. When the green LINK LED is turned on, the ACTentry V-IP is connected to the network. The red TX/RX LED indicates data transmission between the network and the device. Page 7 Issue 3
·
ACTentry V-IP Operating and Installation Manual
2. 5 ACT handset and PC speaker connection
1. The ACT Handset and PC speakers should be connected according to the diagram above. The PC speakers should be powered and switched on. The PC speakers jack plug (green) should be plugged into the ACT handset jack socket (green). The ACT handset microphone jack plug (pink/purple) into the PC soundcard Microphone socket usually symbolised by the following. . .
Microphone 5. The ACT handset speaker jack plug (green) should be plugged into the PC soundcard Lineout or headset jack socket (green). These are usually symbolised by the following:
Line Out
Headset
Page 8
Issue 3
ACTentry V-IP Operating and Installation Manual
2. 6 ACT handset mounting
A handset holder is provided with the ACT handset. This should be mounted in a location that is both easily accessible for the user but not obstructive for the user (as shown below).
Before attaching the holder, clean the mounting area with soap and water, (do NOT use any solvent) and let the area dry. Remove the foil from the adhesive tape and press the holder firmly against the mounting surface. Wait a few hours before hanging up the handset for maximum adhesion. A cable clamp is also provided for cable management. It is also possible to simply place the handset on the desk, without using the mounting holder. If the phone and cord are not impeded, the handset and its switch will function properly.
2. 7 ACTpro-X 1030 Panel-Mount reader installation
ACTentry V-IP may be used in conjunction with an ACTpro access control system. Cardholders present their proximity cards to the panel mount reader to gain access. Visitors use the call button on the door panel. Please see the ACTpro-X 1030 panel mount installation diagram at end of this manual.
Page 9
Issue 3
ACTentry V-IP Operating and Installation Manual
2. 8 ACTentry V-IP software installation
The V-IP unit needs to be powered up and connected to the network before proceeding with the installation. ACTentry V-IP software is designed to operate on a PC connected to a TCP/IP network. [. . . ] To set the ip address enter: setip <ip address> <gateway> <subnetmask> Eg. setip 172. 27. 72. 63 172. 27. 72. 254 255. 255. 255. 0 6. IP address is now set to 172. 27. 72. 63 7. Type quit to exit.
Page 20
Issue 3
ACTentry V-IP Operating and Installation Manual If the V-IP unit does not have a known IP address, then it can be set to a default value by doing the following: 1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ACT ACTENTRY V-IP
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ACT ACTENTRY V-IP will begin.