Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ACT ACTPRO MIFARE PRODUCT RANGE. We hope that this ACT ACTPRO MIFARE PRODUCT RANGE user guide will be useful to you.
Lastmanuals help download the user guide ACT ACTPRO MIFARE PRODUCT RANGE.
Manual abstract: user guide ACT ACTPRO MIFARE PRODUCT RANGE
Detailed instructions for use are in the User's Guide.
[. . . ] ACTpro mifare product range
1040/1050
Rev 1. 3 27/04/2007
General Wiring information
Connection block view of ACTpro mifare 1040/1050.
Wiring for Reader
ACTpro mifare 1040 Sector No: 00005
Test
Powering on the reader requires 12V and 0V to be Connected. Data read from a card is presented on the Data/Clock pins. If configured for wiegand output the D0 signal is available on Data and D1 is available on Clock. [. . . ] The default position of the jumper is for sector operation (jumper on pins 1 and 2). Sector Reader The default sector reader operation of ACTpro mifare readers is to read the batch numbers that are encoded into Sector 1 from the mifare Cards and Fobs issued by ACT. However the readers can be programmed to read any specified sector data, this allows the readers to be installed on sites that are already using mifare cards. See next page for more details on reader re-programming.
Serial Reader When in Serial Reader mode the card serial number of any mifare card that is presented is read. The reader may be placed in serial mode linking pins 2 and 3 together and reapplying power to the board, link should be left in place. The ACTpro mifare reader can also provide the Serial number Byte Reversed, in this case remove the jumper and re-apply power to the reader.
To select Wiegand Output connect SENSE and 0V together. Power must be reapplied for change to take effect, connection should be left in plac
12Vdc Data Clock Sense Buzz 0V Red
Sector/Serial Operation Jumper.
Sector Operation: Jumper Pins 1 and 2
1 2 3
Grn
A B
Serial Operation: Jumper Pins 2 and 3 Serial Operation (Byte Reversed): Remove Jumper
PAGE 2
Unit C1, South City Business Center, Tallaght, Dublin 24, Ireland. E-mail: sales@accesscontrol. ie Web: www. accesscontrol. ie
ACTpro mifare product range
1040/1050
Power On Beep Codes
The Output Data Format and the Sector/Serial Operation of the reader can be determined by the beeps generated by the reader after power is applied. The reader will generate two sets of beeps, the first indicating the Output Data Format and the second set of beeps indicates Sector or Serial Operation. The first set of beeps will occur while the Led is Green, the second set of beeps occur half a second later while the Led is Blue. First Beep Set: Double Beep: Single Beep: Triple Beep: Sector Reader Serial Reader Serial Reader (Byte Reverse) Clock and Data Output Wiegand 37 bit Output
Second Beep Set: Double Beep: Single Beep:
Note: If the reader has been re-programmed (see next page), then a serial of notes is played after the Second Beep Set, this indicates that the readers default programming to read ACT mifare cards has been changed.
Reader Reprogramming
The ACTpro mifare 1040/1050 readers ship from the factory pre-configured to read the mifare Cards and Fobs supplied by ACT. On sites with an existing installation of mifare cards, it will probably be necessary to reprogram the ACTpro mifare 1040/1050 so that the data on the existing cards maybe read. The configuration required by ACTpro mifare 1040/1050 to read the existing mifare cards is given to the ACTpro mifare 1040/1050 via a programming card. The programming card contains the complete information about how to access the data on the existing mifare cards. Programming cards may be supplied by ACT or they can be generated on site if ACTWinPro/ProLite is installed and an ACTpro mifare usb reader is used. To reprogram an ACTpro mifare reader the programming card must be presented to the ACTpro mifare reader after power up and while the Led is Red. [. . . ] A spacer of the correct length is assembled by stacking the spacers together.
View showing spacers stacking
Screws Standard pattress box. Mounting plate is attached to the pattress ox using the screws supplied. Ensure the corect spacers have been used to bridge the gap between the mounting plate and the fixing wings of the pattress box to avoid the mounting plate being distorted.
Security screw supplied with the unit.
Place the cap onto the unit and push firmly into place.
Place the Reader / Keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar.
Mounting Instructions for Surface Mount Unit
The surface mount collar is mounted on the wall using the fixing kit supplied in the box.
Security screw supplied with the unit.
Place the cap onto the unit and push firmly into place.
Place the Reader / Keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar.
PAGE 4 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ACT ACTPRO MIFARE PRODUCT RANGE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ACT ACTPRO MIFARE PRODUCT RANGE will begin.