User manual ADCOM GFA-5006

[. . . ] • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). The water pressure must be within the values indicated in the Technical data table (see adjacent information). [. . . ] NEVER REMOVE the wash cycle pump (black detail) (fig. 4). • Always keep the door of the appliance ajar in order to avoid moisture from forming and being trapped inside the machine. • Clean the seals around the door and detergent dispensers regularly using a damp sponge. This will avoid food becoming trapped in the seals, which is the main cause behind the formation of unpleasant odours. Preventing unpleasant odours Food residue may become encrusted onto the sprayer arms and block the holes used to spray the water. It is therefore recommended that the arms are checked from time to time and cleaned with a small non-metallic brush. The two sprayer arms may both be removed. To remove the upper sprayer arm, rotate the locking ring in an anti-clockwise direction. The upper sprayer arm should be replaced with the holes facing upwards. The lower sprayer arm can be removed by pressing on the side tabs and pulling it upwards. Cleaning the sprayer arms C 1 2 C B A 3 4 After cleaning the filters, replace the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation of the dishwasher. Leaving the machine unused for extended periods If the water hoses are new or have not been used for an extended period of time, let the water run to make sure it is clear and free of impurities before performing the necessary connections. If this precaution is not taken, the water inlet could become blocked and damage the dishwasher. Cleaning the water inlet filter* • Disconnect the appliance from the electricity supply and shut off the water tap. • Leave the door of the appliance ajar. • When you return, run a wash cycle when the dishwasher is empty. * Only available in selected models. 9 Precautions and advice EN This appliance was designed and manufactured in compliance with current international safety standards. The crossed-out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection. For further information relating to the correct disposal of household appliances, owners may contact the relevant public authority or the local appliance dealer. * Only available in selected models. 10 Troubleshooting Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. EN Malfunction: The dishwasher does not start. Possible causes / Solutions: • The pl ug has not b een i nserted i nto t he el ectrical socket pr operly, or ther e is no power i n t he house. • The dis hwasher door has not been shut properl y. • A delayed start has been programmed (see St art-up and us e). • The dis hwasher cycle has not yet fi nished. • The water outl et hose is bent (see I nstall ation). • The filter is clogged up wit h food r esidues. • The dis hes are r at tling against eac h ot her or against t he s prayer arms. • An exc essive amou nt of foam has been produced: the det ergent has not been meas ured out cor rectly or it is not suit abl e f or use i n dishwashers (see Start -up and use). • The level of t he r efined sal t is low or the dos age setti ng is not suited to t he har dness of t he wat er (see Rins e ai d and salt). • The lid on the salt dispens er is not clos ed pr operly. [. . . ] يمكن الحصول على هذه المعلومات من المؤسسات التي تزود‬ ‫منزلك بالماء. - افتح الباب وقم بتشغيل الماكينة بالضغط على زر تشغيل/‬ ‫إيقاف تشغيل. ‬ ‫ اضغط الزر‪ P‬وأبقه مضغوطا لخمس ثوان؛ سيصدر صفيران قصيران‬‫وسيومض ببطء المؤشر المالئم لدرجة القساوة على لوحة التحكم (نظام‬ ‫تخفيف الماء معد افتراضيا إلى الرقم 3). ‬ ‫- اضغط الزر ‪ P‬بشكل متكرر حتى التوصل إلى مستوى قساوة الماء‬ ‫* متوفر في طرازات مختارة فقط. ‬ ‫العناية والصيانة‬ ‫نظف فلتر إدخال الماء الموجود على مخرج الحنفية بشكل منتظم. ‬ ‫ أقفل حنفية الماء. ‬‫ فك نهائية خرطوم إدخال الماء بشكل لولبي، أزل الفلتر ونظفه بعناية تحت الماء‬‫الجاري. ‬ ‫- أعد الفلتر وأعد تركيب خرطوم الماء في موضعه. ‬ ‫•‬ ‫ قم بإقفال حنفية الماء بعد كل دورة غسل لتحاشي التسربات. ‬ ‫• افصل الجهاز عن الكهرباء دائما عند تنظيفه أو أثناء أي عمل صيانة. ‬ ‫قطع إمدادات الماء والكهرباء‬ ‫‪AR‬‬ ‫تنظيف الفالتر‬ ‫مجموعة الفالتر مكونة من ثالثة فالتر التي تزيل األطعمة المتبقية من ماء الغسل ثم‬ ‫تعيد تدوير الماء. يجب تنظيفها إذا أردت الحصول على أفضل النتائج في كل غسلة. ‬ ‫نظف الفالتر بانتظام. ‬ ‫يجب عدم استخدام ماكينة غسل األطباق من دون فالتر، أو إذا كان الفلتر‬ ‫محررا. ‬ ‫• بعد عدة دورات غسل، افحص مجموعة الفالتر ونظفها إذا اقتضت الضرورة‬ ‫بشكل تام تحت ماء جاري، باستخدام فرشاة غير معدنية واتبع التعليمات أدناه:‬ ‫1. أدر الفلتر األسطواني ‪ C‬بعكس اتجاه عقارب الساعة واسحبه إلى الخارج (‬ ‫الرسم 1). ‬ ‫2. [. . . ]