User manual ADCOM GFA-5275

[. . . ] • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). The water pressure must be within the values indicated in the Technical data table (see adjacent information). [. . . ] For further information relating to the correct disposal of household appliances, owners may contact the relevant public authority or the local appliance dealer. Assistance Before contacting Assistance: • Check whether the problem can be resolved using the Troubleshooting guide (see Troubleshooting). • Restart the programme to check whether the problem has ceased to exist. • If the problem persists, contact the Authorised Technical Assistance Service. Never use the services of unauthorised technicians. Please have the following information to hand: • The type of malfunction. This information can be found on the appliance data plate (see Description of the appliance). Saving energy and respecting the environment Saving water and energy • Only begin a wash cycle when the dishwasher is full. While waiting for the dishwasher to be filled, prevent unpleasant odours using the Soak cycle (see Wash cycles). • Select a wash cycle which is suited to the type of crockery and to the soil level of the crockery using the Table of wash cycles: * Only available in selected models. 11 Troubleshooting EN Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. Problem: The dishwasher does not start. Possible causes / Solutions: • • • The plug has not been inserted into the electrical socket properly, or there is no power in the house. The dis hw asher door has not been shut properly. A delayed start has been program m ed (s ee Start-up and use). The The The The dis hw asher cycle has not yet finished. Reprogram m e the m ac hine and restart the was h cycle. Switch off the appliance by pressing the O N/O F F button and switch it back on after a m inute. If the alarm c ontinues, shut off the w ater tap to elim inate the risk of flooding, rem ove the plug from the electrical socket and contact Assistance. The dishes and glasses are covered in a white film or limescale deposits. • • • • The dishes and glasses are • streaked or have a bluish tinge. The crockery has not been dried properly. • • • The dishes are not clean. • • • • • • • • The dishwasher does not take any water in/Tap shut-off alarm (the Salt, Rinse Aid, Drying and End indicator lights flash). • • • • Water loading solenoid valve malfunction alarm (the Salt, Rinse Aid and Drying indicator lights flashes). Water inlet hose alarm/Water inlet filter blocked. (the Salt, Rinse Aid, Washing, Drying and End indicator lights flashes). • • Switch off the appliance by pressing the O N/O FF button. Shut off the water tap to elim inate the risk of flooding and rem ove the plug from the electrical socket. M ake sure the w ater inlet filter has not becom e blocked by various im purities. [. . . ] اگر می خواهید در هر شستشو نتیجه خوبی بدست‬ ‫آورید باید آنها را تمیز کنید. ‬ ‫فیلترها را بطور مرتب تمیز کنید. ‬ ‫ماشین ظرف شویی را نباید بدون فیلتر، یا فیلتر شل استفاده کرد. ‬ ‫• بعد از تمیز کردن فیلترها، مجموعه فیلتر را در جای خود گذاشته و سفت‬ ‫کنید؛ این کار برای نگهداری و راهبری بهینه ماشین ظرف شویی ضروری‬ ‫است:‬ ‫1. فیلتر استوانه ای ‪ C‬را در جهت عکس حرکت عقربه های بچرخانید و‬ ‫بیرون بکشید (شکل 1). ‬ ‫2. فیلتر فنجانی را با کمی فشار آوردن در زبانه های کناری آن بیرون بیاورید‬ ‫(شکل 2). ‬ ‫3. فیلتر صفحه ای ‪ A‬ساخته شده از فوالد ضد زنگ را بیرون بکشید (شکل‬ ‫3). ‬ ‫4. [. . . ]