User manual ADDONICS HDU5SAS

[. . . ] Before the start of the duplication, the duplicator inspects all the target drives and determines which has less capacity than source, then the LCD will show the corresponding channel number. And then automatically copies. The LCD will display the following info. Once the copying process is complete the LCD will display the following results. 3 Compare Compare HDD is used to see if the data on a source hard disk is identical to the target hard disk after the Copy HDD operation. Choose option 2 from the menu: 1 Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disk. The LCD will display the following info Make sure that the capacity of the target hard disk is equal or larger than the source hard disk. [. . . ] By default the first menu option is Copy HDD. Press ENT and the LCD will show the following info. 8. 4 Auto Compare This option automatically compares the source hard disk with the target hard disk after a copy operation is completed. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether fast copy is on or off. (This function currently only effective in FAT, FAT32, NTFS, HFS, Ext2 and Ext3 partitions. ) Press ENT to access option. Use the Up and Down arrow keys to choose On. 8. 9 Auto Start Drive Auto Start Drive is used to automatically enable the copy process once a hard drive is inserted on target port. 8. 5 Button Sound Press ENT to enter the following figure. Use the Up and Down arrow keys to choose. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether button sound is on or off. 8. 10 Auto Start Timer Auto Start Timer is used automatically start duplication after the set time. 8. 6 Device Info This option is used to display the details of all hard disks connected to the copy controller. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 5 Sec-50 Sec. Press ENT and the LCD will display each hard disk' information in order as shown below. 8. 11 Tolerance Size Tolerance Size is used to ensure that when the target is smaller than the source duplication can still be performed by adjusting. 8. 7 System Info This option displays system information. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1%~100% of source. 8. 8 Fast Copy Fast Copy only copies data on the drives. 8. 12 BootTime Delay BootTime Delay is used to to set boot delay time. Press ENT to enter 8. 13 Quick Compare Quick Compare is used to set the size of each comparison unit. Appendix A LCD Messages Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1 Byte/1K/10K/100K/1MB/10MB/100 Mbytes. (In order to improve the accuracy of pure data can maintain the default settings. ) Basic Troubleshooting 6. 1 LCD If the LCD display is blank after the device is turned on, check that the power cable is properly connected and that the power supply is on. 6. 2 Error Message When the system is running a copy operation or hardware diagnostics then operation was manually terminated by pressing ESC, an error message will be shown by the LCD. This may lead to an illegal operation and cause the device to stop reminding. If this happens, the device must be restarted. 6. 3 Hard Disk If unable to read the hard disk please check that the data and power cables are properly connected. When making a copy please make sure that you have set the source hard disk correctly. 6. 4 Keys If pressing the keys on the front panel produces no response from the system, the keys may have malfunctioned. 6. 5 Startup/Shutdown Do not suddenly turn off the power while the system is performing an operation. After shutting down normally, wait a moment (usually around 2 seconds) before starting the system again so it can run its self-diagnostics. Connecting with a HDD: All data will be lost, format?. . . . . . . . . . . . . Delete Image in Partition xx?. . . . . . . . . . . . . Confirm the deleting of data image in partition xx. Format HDD?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ask if you want to format the hard disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Formatting of hard disk has been completed. [. . . ] Flash ROM fail!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Invalid firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The disc doesn't contain a valid firmware. Last update F/W Fail!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]