Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ADDONICS RR2035RPHES. We hope that this ADDONICS RR2035RPHES user guide will be useful to you.
Lastmanuals help download the user guide ADDONICS RR2035RPHES.
Detailed instructions for use are in the User's Guide.
[. . . ] Buzzer Reset: Pressing the button stops the buzzer from making a sound. The buzzer will make a sound when temperature inside the storage rack exceeds the temperature setting on the Thermal Management card. Power LED: Lights up when the power switch is turned on. [. . . ] Setting o o o (40 C, 50 C, 60 C)
Features:
Fan1 to Fan8 could be set either "ENABLE" or "DISABLE". When all the fans are set on "DISABLE", the Fan LED will have no light on. When Ambient temperature (or temperature inside the storage rack) is over the set temperature, the LED will flash and the buzzer will sound.
Hardware Port Multiplier mounted inside the RAID Rack
Floppy power connector SATA host port
J1 Drive Activity LED H Activity LED for eSATA host port lights up when it is connected to a SATA controller card. D0, D1, D2, D3 & D4 - Activity LEDs for port 1, 2, 3, & 4 light up when a drive is connected and blinks when there's drive activity. J3 Error LED H error LED for eSATA host port D0, D1, D2, D3 & D4 - error LED for port 1, 2, 3 & 4
buzzer SATA port 5 SATA port 4 SATA port 1 RAID setting jumper block (J4)
Two Options for Setting RAID on the 5-port HPM-XA
(only select one option) I. Using the JMicron HW RAID Manager utility program For Windows users, install the JMicron HW RAID Manager located on the SATA Controller CD. In the CD, go to RAID utilities > JMB393. This manager can be use to create and monitor the status of the RAID volume.
SATA port 3 SATA port 2 Error and drive activity LED jumper block (J1, J3)
Use the default factory RAID jumper setting when using the JMicron HW RAID Manager.
J4 RAID Setting Jumper Block II. BZS Error buzzer function SET RAID mode setting EZ Automatic rebuilding to M2 RAID mode 2 M1 RAID mode 1 M0 RAID mode 0 Using the onboard RAID setting jumper block (Complete the 7 steps below) Recommended to be used on operating system without JMicron HW RAID Manager support like Linux, Mac & Solaris. Windows users can also used the procedure below. Set the J4 RAID setting jumper block as shown below. (ignore EZ pins, EZ is DISABLED)
spare drive
Default factory RAID jumper setting
1. 4.
Error buzzer function is DISABLED (BZS) RAID mode setting modification is DISABLED (SET) Auto-rebuilding to spare drive is ENABLED (EZ) Individual drive mode is ENABLED (M0~M2)
2. 4.
Note: When the default factory RAID setting is used, independent drive configuration is supported only when connecting to controllers with Silicon Image Sil3124, Sil3132 chip set or controllers that are Port Multiplier (PM) compatible. LED Pin header
Turn on the system power where the HPM is connected for at least 5 seconds for hardware initialization. On the J4 RAID setting jumper block, change (M0~M2) jumper setting to the desired RAID mode using the diagram on the next page as reference. [. . . ] If booted into Windows, in Disk Drives under Device Manager, the raid array will display as "Addonics H/W LARGE" if setup as a RAID0 array. Once raid array is verified, turn off the system then you MUST set back the RAID jumper setting to either: A. Default setting
Notes on RAID Auto rebuild (Diagram shows default factory RAID jumper setting) In reference to the diagram, auto-rebuilding is ENABLED (EZ) When EZ mode is ENABLED, the degraded RAID group will start rebuilding automatically when you install a good drive to replace the failed drive.
Cable Connections For Model: RR2035RPHES & RR2035AXHES 1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ADDONICS RR2035RPHES
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ADDONICS RR2035RPHES will begin.
