User manual ADDONICS RT93DAHXML

[. . . ] This is to help in identifying which drives connects to which ports for easier troubleshooting. Note: The 5 port HPMXA system version PCB board is mounted inside the RAID tower and is connected to the multilane bridge that is mounted at the back of the RAID tower. eSATA Ports Multilane Port www. addonics. com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www. addonics. com/support/query/ RAID Setting Button Dip Switch SATA Host Port (Port 5) SATA Port 2 SATA Port 1 SATA Port 0 SATA Port 3 Floppy Power Connector SATA Port 4 Drive activity LED Jumper Block (J1) Error LED Jumper Block (J3) Dip Switch Settings Raid Mode Individual Drive (Factory Default) 1 OFF OFF OFF OFF OFF OFF OFF Enable ERR Buzzer Function 2 OFF OFF OFF OFF OFF OFF OFF AutoRebuilding to Spare Drive 3 OFF ON ON ON ON OFF ON 4 OFF ON ON OFF OFF ON OFF Port Multiplier Mode 5 OFF ON OFF OFF ON ON ON 0 1 3 5 Clone Large www. addonics. com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www. addonics. com/support/query/ Default factory DIP Switch setting: SW1 ­ RAID Setting DIP Switch BZS ­ Error buzzer function EZ ­ Automatic rebuilding to spare drive (one of the drives on the raid is set as a spare). If EZ is ENABLED anda drive failure occurs, the spare will automatically act as a drive replacement and rebuilding will automatically start. M2 ­ RAID mode 2 M1 ­ RAID mode 1 M0 ­ RAID mode 0 12345 OFF OFF OFF OFF SW1 BZS EZ M2 M1 M0 1. [. . . ] c. 1 2 3 4 5 BZS EZ M2 M1 M0 Press the RAID setting button with a ball point pen. While pressing the RAID setting button turn on the system power where the HPM is connected. The buzzer will sound while holding the RAID setting button. Release it after at least 5 seconds for hardware initialization. A single beep will be heard to indicate initialization is completed. Power off the system power. d. www. addonics. com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www. addonics. com/support/query/ e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode using the diagram below. All settings on the diagram shows · Error buzzer function is ENABLED · EZ function is DISABLED. OFF OFF OFF OFF OFF RAID 0 Mode ON ON ON Clone Mode ON ON SW1 1 2 3 4 5 SW1 1 2 3 4 5 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 OFF OFF OFF OFF OFF OFF RAID 1& RAID 10 Mode ON ON Large Mode ON ON SW1 1 2 3 4 5 SW1 1 2 3 4 5 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 OFF OFF OFF OFF OFF OFF OFF OFF SW1 1 2 3 4 5 SW1 RAID 5 Mode OFF OFF ON 1 2 3 4 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 OFF SW1 1 2 3 4 BZS EZ M2 M1 M0 www. addonics. com Technical Support (M-F 8:30am - 6:00pm PST) OFF 5 Phone: 408-453-6212 Email: www. addonics. com/support/query/ OFF RAID 3 Mode ON Individual Drives Mode 5 RAID Setting Notes: RAID 1& RAID 10 Mode When 2 drives are connected to the HPM-XA, and DIP switch is set to this setting, the 2 drives will be configured as a 2-drive RAID1 array. SW1 1 2 3 4 5 BZS EZ M2 M1 M0 When 4 drives are connected to the HPM-XA, the 4 drives will be configured as a 4-drive RAID10 array. Clone Mode SW1 1 2 3 4 5 BZS EZ M2 M1 M0 Clone's action is similar to RAID1. However, all of the hard drives will be mirrored. Clone mode is useful especially when users like to copy data from a source hard drive to the drives connected to the HPM-XA. f. g. Press the RAID setting button with a ball point pen. While pressing the RAID setting button turn on the system power where the HPM is connected. The buzzer will sound while holding the RAID setting button. Release it after at least 5 seconds for hardware initialization. A single beep will be heard to indicate initialization is completed. Verify if the RAID array is detected by the system. If the 5-port HPM-XA is connected to the motherboard onboard SATA, on the CMOS setup utility, the raid array will display as "Addonics H/W RAID5" if setup as a RAID5 array. If the 5-port HPM-XA is connected to an eSATA host controller card, on the RAID BIOS, the raid array will display as "Addonics H/W RAID0" if setup as a RAID0 array. If booted into Windows, in Disk Drives under Device Manager, the raid array will display as "Addonics H/W LARGE" if setup as a LARGE array. [. . . ] Make sure the power is off (power LED light should be off). Connect the infiniband cable from the back of the tower to the multilane connector on the computer. Power Connector Power Switch Power on/off control a. A main power switch is located at the back of the tower. Another auxiliary switch is located on the front of the tower. [. . . ]