User manual ADT SECURITY MANAGER 2000

[. . . ] Security System User's Manual Security Manager 2000 N75276V2 4/99 Ref. S1632 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to an alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines). About This Manual This manual is a step-by-step guide that will acquaint you with the system's features and benefits. [. . . ] The babysitter code is assigned to user 15. The user of this code should not use the Quick Arming feature described below. Duress Code This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Customer Care Center of your situation, if that service has been provided. Important: This code is useful only when the system is connected to the Customer Care Center. Note that if "Quick Arming" was programmed by the installer, the # key can be pressed in place of the security code when arming the system. If so programmed, the A and B keys on a touchpad can be used for single-button arming AWAY or STAY, respectively. See ARMING ALL PROTECTION and ARMING PERIMETER ONLY sections. The security code must always be used to disarm the system, however. 25 Quick Arming and Single-Button Arming SECURITY CODES (Continued) To Add a User or Change a User's Code Important: Temporary users of the system (e. g. , babysitters, cleaning staff) should not be shown how to use any system function they do not need to know, such as bypassing protection zones for example. Sequential key depressions for all steps in a procedure must be made within 2 seconds of one another, or else the entire entry is aborted and must be repeated from its beginning (e. g. , perform steps 1, 2, and 3 below with no delay between steps). CODE Changing your Master Code Follow this procedure: Enter your existing Master code + [8] + [0][2] + new Master code + new Master code again. 1. + 8 Enter master code, then press CODE key. Example: 7 2 9 6 (Master Code) then press the CODE key. 2. 3. (User Number) Enter user number. Enter the 2-digit User Number (03-16) for the user you are adding or changing. CODE (User's Code) Enter user's code. Enter the new 4-digit security code for that user. Example: 7 2 9 6 To Delete a User 1. + 8 (Master Code) then press the CODE key. 2. (User Number) 3. ----------- Enter user number. Enter the 2-digit User Number (03-16) for the user whose code you are deleting. Wait (about 3 seconds) until the touchpad beeps once before pressing any other key. 26 TESTING THE SYSTEM (TO BE CONDUCTED WEEKLY) Using the 5 TEST Key The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The touchpad sounds a single beep every 40 seconds as a reminder that the system is in the Test mode. N o t e : An alarm message will not be sent to your Customer Care Center during the following tests. Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on if all zones are intact (i. e. , all protected windows, doors, etc. [. . . ] Services rendered outside the normal working hours of ADT are not within the scope of this warranty and any services requested to be performed at such times shall be charged for at ADT's then applicable rates for labor and material. This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on the system. Should it actually be necessary to make repairs to the system due to one of the "conditions Not Covered By Warranty", a charge will be made for such work at ADT's then applicable rates for labor and material. Damage from accidents, acts of God, alterations, misuse, tampering or abuse. [. . . ]