User manual ADT SERIES 4250

[. . . ] USER GUIDE SERIES 4250 AUDIO ALARM CONFIRMATION SYSTEM CONTROL UNIT CONTENTS Page INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Security conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Full Set (Fully armed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Part Set (Partially armed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the fault(s) cannot be immediately cleared and the user needs to set the system, the faulty zone(s) can be omitted from the system by the user with a master code (page 35). This facility is subject to insurance company agreement. Omit key Next key SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Incorrect code entry If the incorrect code is entered during selection procedure the keypad LCD Display will show. Press the RETRY key and enter the correct code. After 3 attempts to enter your code the system will refuse further setting attempts for two minutes and this condition is reported to the Alarm Receiving Centre. After the two minutes have elasped a further 3 attempts may be made. Retry key 10 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Deviation from the Correct Exit Procedure Deviating from the designated Exit route when the countdown period has started will cause the keypad exit bleep to change to a continuous tone. closing any doors on the wrong route will cause the keypad bleeper tone to change to the normal intermittent bleep and you will be able to exit normally. If any zones having been entered by deviating from the exit route are not restored, e. g. doors not closed, within the set exit time the keypad display will show: The FAILED TO EXIT condition will be reported to the Alarm Receiving Centre and the audible tone will continue to sound until the x digit user code is entered. Pressing the * key will display the fault status condition. Eliminate the fault and repeat the FULL SET procedure. 11 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Failure to complete exit procedure If during the FULL SET procedure the user fails to exit the premises with in the set exit time the setting fault condition will be indicated on the keypad LCD as shown: The FAIL TO EXIT condition is reported to the Alarm Receiving Centre and the keypad audible tone will continue to sound. To reset the system, key in your x digit user code and press enter. 12 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PART SET (Partially armed) The PART SET condition allows the alarm system to be armed (set) in certain zones of the protected premises while the remainder of the premises are occupied. Two PART SET selections are available as follows: Delay selection: This feature is selected when access to the non-alarmed (occupied) area is via a protected part of the premises. When the PART SET delay selection is set at the keypad there is a time delay to allow the user to leave the protected area. On entering the protected area by the normal entry route there is a similar time delay to allow the user to key in the x digit user code to UNSET (switch off) the system. During both time delays the keypad will bleep. An example of using this selection is a house with the downstairs protected and the upstairs occupied but the occupants require access to the keypad to PART SET or UNSET the system. 13 Instant selection: This feature is selected when access to the occupied area is not via a protected part of the premises. In this instance the keypad is located outside the protected area eg. a keypad is upstairs enabling the downstairs to be PART SET/UNSET with no time delay. The display will show: Unset key 2) Press the Unset key. 17 UNSETTING THE SYSTEM (TURNING THE SYSTEM OFF) To UNSET the system from PART SET with Instant carry out the following: 1) The keypad display will show: 4) The keypad display will show: 2) Press the Unset key. 3) Key in the x digit user code and press enter. 18 UNSETTING THE SYSTEM (TURNING THE SYSTEM OFF) PROBLEMS WHEN UNSETTING THE SYSTEM Deviation from Entry route Entering the premises via the designated route (Final exit only door), the Entry/Exit buzzer (if fitted) and keypad bleeper will sound intermittently. [. . . ] Arming To carry out multiple partition arming carry out the following using the keypad located in Partition A. If not, carry out the unsetting procedure. 2) Press Full Set key, the display will change and prompt for the master code to be entered. 3) Key in the x digit master code and press enter. [. . . ]