User manual ADVANCE XI125

[. . . ] HEED WARNINGS All warnings on the appliance and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. WATER AND MOISTURE The appliance should not be used near water for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. VENTILATION The appliance should be situated so that its location or position does not interfere with its proper ventilation. [. . . ] Push one time the center of this multifunctions button and the display indicates INPUT. Turn the button and you can choose a different source. You can repeat same way to navigate in the menu. Arborescence des menus et options / Options and menus arborescence Menüstruktur und Optionen / menu e le opzioni 20 N 0-60 BAS -10 +10 TRE -10 +10 * Only when BPA is Off / Uniquement quand BPA est Off /Nur wenn BPA Off BAL BPA SPE VOL 0-60 R 0-20 L 0-20 OFF ON LOU A OFF ON B A+B Turn the button Tourner le bouton Den Knopf drehen ruotare la manopola Push the button Pousser sur le bouton Den Knopf drücken Premere il tasto Menu when BPA is Off O INP CO1 n CO2 n OPT n PHONO n CD n TUNER AU1 n AU2 n AU3 n AU4 n PC2 n USB n USA CONNEXIONS FACE ARRIÈRE - REAR PANEL CONNECTIONS RÜCKSEITIGE ANSCHLÜSSE - PANNELLO POSTERIORE COLLEGAMENTI t o a sd f g h r q y e w i u q ENTRÉES DES SOURCES Vous devez connecter vos sources sur les entrées stéréophoniques correspondantes. INPUTS You can connect your stereo sources on those inputs. These inputs are suitable for any line level source equipment such as tuners, CD players, DVD, MP3 players, etc. Note: These inputs are only for analogue audio signals. They should not be connected to the digital output of a CD player or any other digital device. PHONO INPUT AND GROUND TERMINAL You can connect your turntable on the RCA connectors left (L) and right (R). Turntables normally includes a single wire earth lead. Use the phono ground connector to connect this lead. Unscrew the terminal to expose the hole which will accept the lead. After insertion, tighten the terminal to secure the lead. PRE OUT / PREAMPLIFIER OUTPUTS If you want to use a more powerful power amplifier and use the X-i120 as a preamplifier, connect it to the PRE OUT jacks, and connect all speakers to the power amplifier. You need to remove the U bridge first between PRE-OUT and AMP IN. IN / POWER AMPLIFIER IN If you only want to use the power amplifier section of your X-i120, you can connect another preamplifier or audio mixer on L/R AMP. REC OUTPUT This analog audio ouput are for connecting a recorder with an analog audio input such as a cassette deck, MD recorder, etc. Connect the right speaker to the terminals market ‘R +’ and ‘R-’ ensuring that the ‘R+’ is connected to the ‘+’ terminal on your loudspeaker and the ‘R-’ is connected to the loudspeaker’s ‘-’ terminal. Connect the terminals marked ‘L+’ and ‘L-’ to the left speaker in the same way. When using both SPEAKERS A and SPEAKERS B connect speakers of impedance 8 Ohms or greater. SPEAKERS B (only for X-i90): use same method to connect the B pair. The high current binding post terminals can be used as a screw terminal for cables terminating in spade or pin connectors or for cables with bare wire ends. [. . . ] You will see a new bluetooth connection under ADVANCE ACOUSTIC name. Confirm that you choose it, after few seconds, your audio device is pairing with the WTX-500. If pairing is ok, then, the blue led of the Air amplifier will be fixed. You don’t need any Pin code confirmation. [. . . ]