User manual AEG-ELECTROLUX 111K-D

[. . . ] When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. Never use plastic or aluminium foil dishes on the hob. [. . . ] cooked in well covered saucepans cook at lower temperature which is more economical. q q Ensure pans are large enough to avoid liquids being split onto the plates. Never leave the plates on without a pan on them or with an empty pan on them. Take care never to lean or reach over a hot electric plate. Always point pan handles inward or over the work surface next to the hob to avoid accidentally knocking over a pan as you pass by. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. If the control knobs become difficult to turn, please contact your local AEG Service Centre. 8 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. The Hotplates Spills onto the actual plate should be removed using warm water and a soft brush, nylon or plastic scourer. To keep the plates looking as new, hotplate conditioner can be purchased from most hardware stores, e. g. "4 Hob" by HomeCare Products (follow the manufacturer's instruction for use). Alternatively, wipe the plates with a drop of olive oil on a kitchen towel to avoid rust. It is important to note that the plate will smoke a little and produce a slightly unpleasant odour when next used. 9 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM s SOLUTION x The plate does not heat up. x x x Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the correct control knob has been turned. Check the plate is clean and dry Check the cooking pan is the correct size for the plate. Check the cooking pan has a flat bottom Check the setting is correct for the type of cooking. s The plate is not giving satisfactory results x x x x If after all these checks, your hob still does not operate correctly, contact your local AEG Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 10 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. When you contact the Service Centre, they will need the following information: 1. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5. [. . . ] 3) Connect the red (live) wire to the terminal which is marked with the number 1. FO 0488 4) Connect the black (neutral) wire to the terminal which is marked with the number 4. 5) After fitting a green or yellow/green sleeve over the bare copper wire (earth wire), connect the exposed end to the terminal which is marked with the earth symbol or with the number 5. NOTE: The earth wire should be about 2 cm. 6) Secure the cable by means of the clamp screws and refit the terminal block cover. 18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. [. . . ]