User manual AEG-ELECTROLUX 111K-W

[. . . ] Ensure the control knobs are in the `OFF' position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. [. . . ] "4 Hob" by HomeCare Products (follow the manufacturer's instruction for use). Alternatively, wipe the plates with a drop of olive oil on a kitchen towel to avoid rust. It is important to note that the plate will smoke a little and produce a slightly unpleasant odour when next used. Failure to clean and condition hotplates may lead to rust and corrosion forming on the surface. Stainless steel parts: the stainless steel spill rings may become straw coloured with use. Use a proprietary stainless steel cleaner to remove this straw discolouration. This also applies to the area around the hotplates on stainless steel hobs. 8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the correct control knob has been turned. Check the plate is clean and dry Check the cooking pan is the correct size for the plate. Check the cooking pan has a flat bottom Check the setting is correct for the type of cooking. The plate is not giving satisfactory results If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 9 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. When you contact the Service Centre, they will need the following information: 1. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5. Date of purchase Customer Care For general enquires concerning your AEG-Electrolux appliance or for further information on AEGElectrolux products, please contact our Customer Care Department at the address below or visit our website at www. aeghome. co. uk Customer Care Department AEG-Electrolux Domestic Appliances 55-77 High Street Slough Berkshire SL1 1DZ Tel : 08705 350350 10 Guarantee Conditions AEG-Electrolux offers the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where defects or poor performance are due to misuse, accidental damage, neglect, faulty installation, unauthorised modification or attempted repair, commercial use or failure to observe requirements and recommendations set out in the instruction book. This guarantee does not cover such parts as light bulbs, removable glassware or plastic. Should guarantee repairs be necessary the purchaser must inform the nearest AEG-Electrolux Service Force Centre (manufacturer's service or authorised agent). AEG-Electrolux reserves the right to stipulate the place of the repair (i. e. [. . . ] NOTE: The earth wire should be about 2 cm. 6) Secure the cable by means of the clamp screws and FO 0488 refit the terminal block cover. 15 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. [. . . ]