User manual AEG-ELECTROLUX 115EDB

[. . . ] If your appliance has been equipped with a mains lead with a moulded-on type plug, you must comply with the following regulations: The plug moulded on to the lead incorporates a fuse. For replacement, use a 5 amp BS1362 fuse. Only ASTA approved or certified fuses should be used. If the fuse cover/carrier is lost, a replacement cover/carried must be obtained from an electrical goods retailer. [. . . ] If a fixed connection is required the cooker hood should be connected by an electrical installer registered with a competent electricity company. An isolating device is to be provided on the fixed wiring side. Switches with a contact opening of more than 3mm apply as isolating devices. These include-automatic cut-out switches, fuses and contactors (VDE 0730, s. 7, Part1). 5 Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology "DOUBLE POLE" means that both the live and neutral supplies are swiched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. IMPORTANT The wires of the mains lead supplied with this appliance are coloured in accordance with the following code: Blue-Neutral Brown-Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The whire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. BLUE (NEUTRAL) BROWN (LIVE) Appliances with 2 wires LOAD L N LOAD L SUPPLY DP 13A, 250V FUSE ON N SUPPLY 6 Appliances with 3 wires Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. 5 10 Wall mounting -- Position the template on the wall. -- Drill four 8 mm Ø holes in the wall, 2 in points H and 2 in points I. -- Fit the four 8 mm screw anchor plugs in the wall. -- Screw two 5 x 45 mm screws in points H but do not tighten them fully home. -- Adjust the unit so that it is positioned at a right angle to the wall by turning the two support screws G. -- Now hang the hood on the wall (holes H). Tighten the first two screws and, for safety's sake, screw the other two 5 x 45 mm screws into the holes in the hood. 6 H 36, 5 G I 6 G 46 13 11 Hood Operation The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The control switches are located on the unit's front panel: the light switch switches the hood lamp on and off; the motor switch switches the cooking smoke and vapour extractor motor on and off, enabling you to select one of the four different speeds. Light switch On/Off 6 Motor continuous sliding switch Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. [. . . ] The metal grease filter is positioned on the inside of its related support grille. Leave the metal grease filter panel to soak for approximately 1 hour in very hot water with grease-dissolving detergent and then rinse it with very hot water. Load the grease filter panel in a dishwasher, selecting the most intensive washing programme and maximum temperature, at least 65½C. The grille should be cleaned with luke warm water and nonabrasive detergent when you change the filter. [. . . ]