User manual AEG-ELECTROLUX 2000D-M

[. . . ] 2000 D Dunstabzugshaube Fume Extractor Hood Montage- und Gebrauchsanweisung Installation and Operating Instructions Contents Introduction Extractor version Filter version Electrical connections Safety warnings for electrician Technic Details Installation Safety warnings for kitchen unit installer Installation Safety warnings for user V iew of the hood Hood Operation Setting the fan speed Hood lighting Intensive speed P Fan timer Switching off the fan Maintenance and care Warnings on the activated carbon filter Display warning on saturation of activated carbon filter Display warning on saturation of metal grease filter Warning Replacing light bulbs Cleaning Special accessory Technical assistance service 28 28 29 30 30 31 32 32 34 38 39 39 40 40 41 41 42 43 43 44 46 48 48 49 49 49 27 Introduction Extractor version q The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). q You will need original AEG activated carbon filters for this function (see Special Accessories). q The air is forced out through a hose fitted to the connection flange q The outlet hose must have a diameter of 150 mm (special accessory) for the filtering version. q If the cooking vapour is passed through an outside wall, you will need an MKZ150 telescopic wall pipe E-Nr. : 942 118 609 (150 mm Ø) from our range of special accessories. 28 Filter version q The air is filtered through an activated carbon filter and passed back into the kitchen through the top outlet duct grids. [. . . ] The hood is supplied with a reducer for 120 mm diameter pipes. This reducer must be mounted on the hood outlet. q Filter operation If the connector ring has not yet been installed, it must be fitted at this point (Q in Q 7, Fig. Turn it in a clockwise direction and fix it to the air pipe L using a screw. Insert the air pipe into the Q telescopic chimney L support and fix it with four screws (Ø 2, 9 x 9, 5 mm). Fix the 150 mm diameter ABS pipe to the hood outlet, and connect it to the air pipe connector Fig. For both versions: q The hood can now be connected to the power supply. q If a gas non-return valve has been installed or is required, ensure that it opens and closes properly. q Fix the top part the telescopic outlet pipe to the relative support, using the two 3 mm dia x 9 mm screws R. q Slide the bottom part of the telescopic outlet pipe downward until it rests in its housing on the top of the hood. q Replace the grease filters. 37 Safety warnings for user q Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. q Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. q The risk of a fat fire increases when using dirty oil. q It is extremely important to note that overheating can cause a fire. q Never carry out any flambé cooking under the hood. q Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). q It is very important to clean the hood and replace the filter at the recommended intervals. Failure to do so could cause grease deposits to build up, causing a fire hazard. 38 V iew of the hood 1. Control panel Lighting units Metal grease filters Telescopic chimney Outlet grids for Filter version 4 1 2 3 3 5 3 Hood Operation Bild 8 q The control panel is located on the front of the hood. q The control panel numbers and symbols (Fig. to right) are explained in the key below: = Lighting, on/off. [. . . ] Refit the grease filters when it are dry. Dishwasher machine Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when it are dry. [. . . ]