User manual AEG-ELECTROLUX 21601G-W

[. . . ] 20604 G 21601 G - 21602 G 21604 G Gas hob Table de cuisson Kochmulde Gaskookplaat Operating and Installation Instructions GB Notice d'utilisation et d'encastrement BE/FR Gebrauchs- und Einbauanweisung BE Gebruiksaanwijzing en Installatievoorschrift NL/BE ENGLISH Important Safety Information GB You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation q This hob must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob. [. . . ] Check the burner cap and crown have been replaced correctly, e. g. after cleaning. s The gas ring burns unevenly x x If after all these checks, your hob still does not operate correctly, contact your local AEG Service Force Centre. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 9 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to the your local Service Force Centre. When you contact the Service Centre, they will need the following information: 1. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5. Date of purchase CUSTOMER CARE For general enquiries concerning your Electrolux appliance and for further information on AEG products, contact our Customer Care Department by letter or telephone as follows: Customer Care Department AEG Domestic Appliances 55 - 77 High Street Slough Berkshire SL1 1DZ Tel : 08705 350350 10 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handled over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where defects or poor performance are due to misuse, accidental damage, neglect, faulty installation, unauthorised modification or attempted repair, commercial use or failure to observe requirements and recommendations set out in the instruction book. This guarantee does not cover such parts as light bulbs, removable glassware, dust bags or filters. Should guarantee repairs be necessary the purchaser must inform the nearest customer service office (manufacturer's service or authorised agent). IGNITION HT SPARK Spark Generator Ispra Control's BF 50046 - 230-240V 0. 6 YA T120 Spark Gap : Fixed 2. 0 kW (6824 BTU/HR) 3. 0 kW Natural Gas (10236 BTU/HR) 2. 8 kW L. P. G. (9554 BTU/HR) 2. 0 kW (6824 BTU/HR) 1. 0 kW (3412 BTU/HR) HEAT INPUT Rear Left Burner (semi rapid) Front Left Burner (rapid) Rear Right Burner (semi rapid) Front Right Burner (auxiliary) APPLIANCE CLASS APPLIANCE CATEGORY GAS SUPPLY 3 II2H3+ Natural gas G20 / 20mbar 12 BURNER TYPE OF GAS POSITION NOMINAL THERMAL POWER NOMINAL FLOW RATE NOZZLE REFERENCE 1/100 mm NOMINAL THERMAL POWER NOMINAL FLOW RATE NOZZLE REFERENCE 1/100 mm RAPID (large) MAX MIN SEMI-RAPID (medium) MAX MIN AUXILIARY (small) MAX MIN NATURAL GAS 20 mbar VALUE = 37. 78 MJ/m3 Ws - 50. 7 MJ/ m3 kW m3/h 3. 0 0. 286 119 0. 65 0. 057 Adjust. 2. 0 0. 190 96 0. 45 0. 038 Adjust. 1. 0 0. 095 70 0. 33 0. 028 Adjust. LPG GAS 28-30/37 mbar VALUE = 49. 92 MJ/Kg kW g/h 2. 8 202 86 0. 65 43. 5 40 2. 0 144 71 0. 45 29 32 1. 0 72 50 0. 33 21, 5 28 Burner Auxiliary Semi-rapid Rapid Dia. Tap By-pass 1/100 mm 28 32 40 Aeration adjustment none 13 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B. S. The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. [. . . ] Resistance should be less than 0. 1 (Ohm), check all earth wires for continuity and all contacts clean and tight. INSULATION CHECK Appliance electrically disconnected, all switches ON. Test leads from L to N in appliance terminal block. If meter reads «0» then there is a short circuit. [. . . ]