User manual AEG-ELECTROLUX 2300BGW

[. . . ] 9 Something not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Service & spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Guarantee conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 For the installer Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is not designed for commercial/industrial purposes. Ensure that all the control knobs are in the OFF position when not in use. Do not use the appliance if it is damaged in any way. If a fault or crack becomes visible, disconnect the appliance immediately from the electricity supply and contact your Disposal Make the appliance unusable by cutting off the cable. Dispose of any packaging material and old appliances at an authorised disposal site. 4 Description of the product Pilot light Control knobs Ceramic glass griddle Pilot light Kontrolleuchte für die Kombi-Grill 30 25 0 5 10 20 15 Griddle control knob Minute timer control knob 5 Operating instrutions Operating instructions griddle Griddle control knob Variable griddle temperature "1" - low heat "9" - high heat "0" - off Control light 30 25 0 5 10 20 15 Operating instructions Minute Timer Turn control knob to set desired number of minutes - maximum 30. The timer has no electric connection with the griddle element and can be used independently of it. 6 Hints on the ceramic glass griddle Ceramic glass is insensitive to temperature shock and very robust, however it is not unbreakable. Hard and sharp objects, in particular, can damage the cooking surface if they fall on it. Warning If visible cracks appear in the surface, the appliance must be disconnected from the mains immediately. Spillages of plastics and other meltable materials such as sugar and food containing sugar (also applies to food with a natural sugar content to which no extra sugar has been added), such as marmalade, jam, fruit juice, etc. must be wiped off the ceramic surface while still hot. Failure to do this could cause the griddle to peel and crack. Use the enclosed glass scraper and polish with a ceramic glass cream cleaner afterwards. Use the rough side of a scouring sponge to apply more water and detergent (washing-up liquid or liquid scouring agent) to the glass surface. Remove the dirty water with kitchen roll. Apply more water and washing-up liquid, using the rough side of a scouring sponge. Scour thoroughly. 9 Installation Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The appliance unit can be mounted in any type of kitchen with a work top whose thickness is between 28 mm and 40 mm. Clearance The distance between the top side of the work top and the carpentry underneath must be at least 47 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the work top. Tighten the brackets on to the work top with an ordinary screwdriver. Cut-out measurements One rectangular hole is sawn out for the appliance combination chosen. The depth of the cut-out for any unit is: 490 mm Length of hole = sum of all units` externally measured length, less 20 mm. Minimum distance to side wall: 150 mm Minimum distance to rear wall (nonflammable material): 150 mm Mounting of Reinforcement Beams A reinforcement Beam, with supporting flanges at each end, is included with each two-burner unit. For unit combinations, a reinforcement beam must be used between each unit. Reinforcement beams 10 Min. 47 mm It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. The units externally measured length 145 mm: Cooker hood 290 mm: Two-zone ceramic-top electric hob Two-burner gas hob Grill Fryer Wok 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob 725 mm: Four-zone ceramic-top electric hob Installation of a single unit When mounting a single unit, be it a half-or full size unit, in a worktopsurface which is thicker than 30 mm, it is necessary to make a special notch in both sides of the cutout hole, as shown in the adjacent drawing. The purpose of these notches is to create space for the electrical cables. 11 Electrical connection The electrical connection may only be performed by a qualified electrician/ competent person. The electrical connection must be carried out in accordance with prevailing regulations for appliances using heavy current. The connection must comply with any specific requirements specified by the local electricity supply authority. [. . . ] Contact your local AEG Service force centre. Fuses constantly blowing? If after all these checks, your appliance still does not operate correctly, contact your local AEG Service Force Centre. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. 14 Service & spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will automatically be routed to the Service Centre covering your post code area. In-guarantee customers should ensure that the recommended checks under the heading "Something Not Working" have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. [. . . ]