User manual AEG-ELECTROLUX 25658G-M

[. . . ] INSTRUCTIONS AND ADVICE FOR THE USE, INSTALLATION AND MAINTENANCE OF MIXED AND GAS FUELLED BUILT-IN HOT PLATES Dear Customer, Thank you for having purchased one of our products. We are certain that this new, modern, functional and practical appliance, built with the very highest quality materials, will meet your requirements in the best possible way. It is, however, important to thoroughly read the instructions in this handbook in order to obtain the best results. These instructions are only valid for the countries of destination, the identification symbols of which are indicated on the cover of the instruction manual and on the appliance itself. [. . . ] - 73/23 + 93/68 regarding electrical safety. FIG. 13 12 INSTALLATION 10) INSTALLING THE HOT PLATE WITH THE BATTERY Check that the appliance is in a good condition after having removed the outer packaging and internal wrappings from around the various loose parts. In case of doubt, do not use the appliance and contact qualified personnel. Never leave the packaging materials (cardboard, bags, polystyrene foam, nails, etc. ) within children's reach since they could become potential sources of danger. The measurements of the opening made in the top of the modular cabinet and into which the hot plate will be installed are indicated in either fig. Always comply with the measurements given for the hole into which the appliance will be recessed (see fig. 9/A ­ 9/B and 10). The appliance belongs to class 3 and is therefore subject to all the provisions established by the provisions governing such appliances. 11) FIXING THE HOT PLATE The hot plate has a special seal which prevents liquid from infiltrating into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal: - Detach the seals from their backing, checking that the transparent protection still adheres to the seal itself. - Overturn the hot plate and correctly position seal "E" (fig. 11) under the edge of the hot plate itself, so that the outer side of the seal perfectly matches the outer perimetral edge of the hot plate. The ends of the strips must fit together without overlapping. - Unscrew the ignition cap "T" (see fig. 14) and fit a 1, 5 V battery (not included in the appliance) with the positive "+" polarity turn inside. - Evenly and securely fix the seal to the hot plate, pressing it in place with the fingers. - Fix the hob with the proper brackets "S" and fit the prominent part into the porthole "H" on the bottom; turn the screw "F" until the bracket "S" stick on the top (fig. 14 13 ADJUSTMENTS Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. Check that the flame does not go out when the knob is sharply switched from the "Full on" to the "Reduced rate" position. It is understood that only burners operating with G20 gas should be subjected to the above mentioned adjustments. The screw must be fully locked when the burners operate with G30 or G31. 12) TAPS "Reduced rate" adjustment - Switch on the burner and turn the relative knob to the "Reduced rate" position (small flame fig. 1). 15) of the tap, which is simply pressed on to its rod. [. . . ] Rating = 1500 W CHINA MARKET WITH BATTERY 4 BURNERS LPG = 30 mbar NATURAL = 20 mbar TOWN (SHANGHAI) = 10 mbar TOWN (GUANGZHOU) = 20 mbar Tot. LPG = 545 g/h Voltage = 1. 5 V DC 4 BURNERS WITH UR LPG = 30 mbar NATURAL = 20 mbar TOWN (SHANGHAI) = 10 mbar TOWN (GUANGZHOU) = 20 mbar Tot. Gas Rate = 7. 85 kW Tot. Nom. Towngas Rate = 7. 6 kW Tot. LPG = 571 g/h Voltage = 1. 5 V DC 25 TECHNICAL DATA ON THE DATA LABEL COREA MARKET 4 BURNERS LPG = 28 - 30 mbar NATURAL = 20 mbar Tot. [. . . ]