User manual AEG-ELECTROLUX 25742G-M

[. . . ] 534403 701 Use and installation instructions GB © Electrolux Household Appliances Ltd 2001 Installation options On base cabinet with door When constructing the cabinet, suitable precautions must be taken to prevent contact with the casing of the hob, which becomes very hot during operation. The recommended method for overcoming this problem is illustrated in fig. The panel underneath the hob must be easily removable to allow the hob to be locked in position and released in case of servicing work. 1 a Removable panel b) Space for connections 30 For Your Safety These instructions have been drawn up for your safety and that of others. You are therefore requested to read them carefully before installing and using the appliance. [. . . ] The result should be a small, homogeneous flame which is uniform around the entire burner ring. 5) Finally, check that the burner does not go out when the tap is turned quickly from the maximum to the minimum position. A Suggestions and Advice Information concerning environmental protection This appliance complies with the following EEC Directives: - 73/23 and 90/683 (relating to Low Voltage); - 89/336 (relating to Electromagnetic Compatibility); - 90/396 (relating to Gas Appliances) - 93/68 (relating to the General Standards) and subsequent amendments. 16 5 Description of the hob 2 6 4 1. Hob 2. Medium semi-rapid burner 3. Small auxiliary burner 4. Large rapid burner 5. Burner control knobs 6. Triple flame burner Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED. All external wiring must comply with the IEE Regulations for the Electrical Equipment of Buildings. The electrical supply can be by either a plug and socket or a permanently wired connection via a double - pole switch. Should the plug (where supplied) not fit the socket in your home, it should be removed and replaced with a suitable plug. Note: If a moulded plug is fitted which is not suitable, it must be cut off and disposed of properly. To avoid the risk of electrocution, the moulded plug must not be left where children might find it and plug it into a supply socket. It must not be used for any other appliance. Three pin plugs to BS1363 with a capacity of not less than 13A must be used and fitted with a 3 amp fuse `ASTA' approved to BS 1362. With moulded plugs, after replacing the fuse the cover must be refitted. If the cover is lost, the plug must not be used until a replacement cover has been obtained from your supplier. The colour of the correct fuse cover is that of the coloured insert in the base of the fuse recess, or stated elsewhere on the plug. Always state this colour when ordering a replacement fuse cover. If you wish to make a direct connection to the mains, an omnipolar switch with a gap between the contacts of at least 3 mm, of suitable rating for the load and complying with the regulations in force, must be installed between the appliance and the mains. The switch must not break a contact in the yellow/green earth wire. YES BAND CLAMPS COPPER PIPE OR STAINLESS STEEL HOSE 3 5 1 2 Service opening in cabinet REAR VIEW Instructions for use Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. NO The hob control knobs The symbols on the control knobs mean the following: no gas flow maximum gas flow minimum gas flow REAR VIEW Important All operating positions must be set between the maximum and minimum flow settings, and never between the maximum setting and the closed position. D Fig. 1 A A C B C B A-Burner cap B-Lighting plug C- Thermocouple D-Triple flame cap The wires in the mains lead are coloured in accordance with the following code: GREEN AND YELLOW. . . . . . . . EARTH BLUE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NEUTRAL BROWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LIVE The wires should be connected into the terminal of your plug as follows: EARTH: to the terminal marked E, or coloured GREEN or GREEN / YELLOW. NEUTRAL: to the terminal marked N, or coloured BLACK or BLUE. LIVE: to the terminal marked L, or coloured RED or BROWN. When wiring the plug ensure that all strands of wire green and yellow (earth) are retained in each terminal. Ensure that the main connection pipe does not exert any stain on the hob. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Correct use of the hob For lower gas consumption and to ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Also, as soon as a liquid comes to the boil take care to turn the flame down to a level that will just keep it boiling. [. . . ] The guarantee covers all parts or components witch fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where defects or poor performance are due to misuse, accidental damage, neglect, faulty installation, unauthorised modification or attempted repair, commercial use or failure to observe requirements and recommendations set our in the instruction book. This guarantee does not cover such parts as light bulbs, removable glassware or plastic. Should guarantee repairs be necessary the purchaser must inform the nearest AEG Service Force Centre (manufacturer's service or authorised agent). [. . . ]