User manual AEG-ELECTROLUX 2600D-A

[. . . ] 12 Safety instructions These warnings are provided in the interest of your safety. Ensure that you understand them all before installing or using the appliance. If you are unsure about any of these meanings or warnings contact the Customer Care department Please retain this instruction book for future reference, particularly if the appliance is sold or left to another person. Installation and service q q q q q Any electrical installation of the cooker hood must be carried out by a qualified electrician and the hood itself must be installed by someone with experience. Installation made by an unqualified person can lead to loss of function of the cooker hood and possible damage to person and and/or property. The cooker hood must be at least 50 cm above electric hobs or electric ranges, or at least 65 cm above gas burners or gas ranges. [. . . ] To switch off the saturation detection : depress and hold the A and B buttons for 3 seconds until the LED indicator for the active carbon filter is flashing. Led ­ Indicator for grease filter C The LED indicator for the grease filter will flash when it requires cleaning. Follow the maintenance instructions. Led - indicator for charcoal filter D The LED indicator for the charcoal filter illuminates when the filter requires replacing. This occurs after about 160 working hours from when the active carbon filter was first put into operation. Resetting the saturation indicator After cleaning or replacing the filter depress and hold the G and H buttons again for 3 seconds until the grease filter LED or the charcoal indicator LED are no longer flashing. 5 Maintenance and cleaning Before doing any maintenance work on the hood, disconnect it from the main supply by disconnecting the plug from the wall socket or unscrewing the fuse. Cleaning the hood Clean the outside of the hood using a damp cloth and a mild detergent. Never use corrosive, abrasive or flammable cleaning products. Cleaning the grease filters Clean the filter every month or every other month according to how much the hood is used. The cleaner the filters, the more grease they collect. 3): q Push the handle towards the rear of the hood. q Pull the filter down at the front and remove it forwards. The filter is made of aluminium wires on which the grease collects. Clean the filter in hot water using a detergent, or in a dishwasher. Let the filter dry before putting it back. Note that a dishwasher may discolour the filter. Fig. 3 Changing and cleaning the carbon filter Only applicable for recirculation. The carbon filters absorb smells and odours. Unlike other carbon filters, the LONGLIFE carbon filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month. The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the carbon, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100º C. The KFL 60/80 carbon filter can not be reactivated, it has to be changed after 6-8 months of normal use. 6 After approximately three years of use, the KF8 filter should be replaced with a new, as the odour reduction capacity will be reduced. q Press the red buttons (A), lower the front of the carbon filter. The grease that collects in the filters and the duct could ignite if a hot plate is left on (or if overheating occurs). Remove the upper glass panel The upper glass panel can be removed for cleaning (Fig. [. . . ] q Insert the rawl plugs (7) and hang the hood on the wall again. Adjust it horizontally with the screws (8) and secure it with the screws (9) q Mount the chimney holder (10) with the rawl plugs (9a) and the screws (11). Be careful that it is centered over the hood and horizontally aligned. q Fitting for ducting (S) Connect a tube between the hood air outlet and the wall or roof exhaust channel. Fix it with the tube clamps supplied. Fitting for recirculation Mount the recirculation spigot (12) with the two screws (13) supplied. Mounting the chimney Place the chimney and fix it to the top chimney holder with the two screws (16) supplied. [. . . ]