Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AEG-ELECTROLUX 3010D-M. We hope that this AEG-ELECTROLUX 3010D-M user guide will be useful to you.
Lastmanuals help download the user guide AEG-ELECTROLUX 3010D-M.
Manual abstract: user guide AEG-ELECTROLUX 3010D-M
Detailed instructions for use are in the User's Guide.
[. . . ] · Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. In this case the hood will be slightly more noisy. · When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers 600 mm gas cookers 650 mm coal and oil cookers 700 mm min. · The national Standard on fuel-burning systems specifies a maximum depression of 0. 04 bar in such rooms. [. . . ] Follow the maintenance instructions.
Led - indicator for charcoal filter E
The LED indicator for the charcoal filter illuminates when the filter requires replacing. This occurs after about 160 working hours from when the active carbon filter was first put into operation.
Resetting the saturation indicator
After cleaning or replacing the filter depress and hold the A button again for 3 seconds until the grease filter LED D or the charcoal LED E are no longer flashing.
68
Maintenance and care
· The hood must always be disconnected from the electricity supply before beginning any maintenance work.
Metal grease filter
· The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks.
Open the metal grease filter
· First, push the metal grease filter stop backwards, then extract the filter, pulling downwards. Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher machine Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur, this does not have any impact on its performance.
Fig. 4
· Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes).
69
Charcoal filter
· The charcoal filter should only be used if you want to use the hood in its filtering function. · To do this you will need an original AEG charcoal filter (see special accessories). · Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month (when using the hood 2, 5 hours per day, in avarage). The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100º C. After approximately three years of use, the charcoal filter should be replaced with a new, as the odour reduction capacity will be reduced. · Mounting Remove the frame i which supports the filter h by turning 90° the two knobs g, Fig. 5. Insert the coal mattress inside the frame and put all parts back in their place. · To dismount proceed in reverse order. · Always specify the hood model code number and serial number when ordering replacement filters. [. . . ] In case the hood is to be used in filter version, mount the deflector F on the chimney support with four screws 2, 9x6, 5 and fit an exhausting pipe (15) to connect deflector to the outlet hole D of the hood. In case the hood is to be used in exhausting version, then the deflector must not be mounted and fit an exhausting pipe (15) to connect outlet hole D of the hood to the outside. · Make electrical connection (16), but leave the hood disconnected from the home general electric panel. · Connect lamps and control panel to the motor housing (17). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX 3010D-M
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX 3010D-M will begin.