User manual AEG-ELECTROLUX 3200B-DGB

[. . . ] Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck! 3 The symbols you will see on some paragraphs of this booklet have the following meaning: The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance. The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. [. . . ] Even though you may have only put wet clothes into an empty bowl, the delay before spin will still occur to be safe and to protect your washing machine. Turn the program selector dial to the required program. The Display shows the duration of the selected program. The selector dial is divided into following sections. Regular Wash and Fast Wash ; Colours, Delicates, Heavy Soil, Woollens, Handwash, Bedding, Rinse+Spin, Drain+Spin and Tub Cleaning. The Program Selector knob is not a timer. Once you select a wash program, the Program Selector knob will stay at that position for the whole wash cycle. If you do move the Program Selector Knob the effect will be different depending on the status of the machine at the time you do this, as follows: 1. When the machine is in PAUSE mode, moving the Knob to a new position will result in the machine resetting to the start of the new program. When the machine is running, moving the Knob to a new position will result in the machine continuing the wash and it will show " " on the display with 3 consecutive short 14 Program Option Buttons Depending on the program, different functions can be combined. These must be selected after choosing the desired program and before depressing the "Start/Hold To Pause" button. When these buttons are pressed, the LED lights come on and you will get a information shown in the digital display. Wash Load Option 1. This option MUST be selected after choosing the wash program with the dial, and before pressing the "Start/Hold To Pause" button. If after having set the Delay-End option (and pressed "Start/Hold To Pause" button) and you wish the cancel or modify it, follow the below steps: 1. set the washing machine to PAUSE by press and hold the "Start/Hold To Pause" button for 1. 2 seconds 2. deselect the Delay-End option, changing the status 3. press the "Start/Hold To Pause" to start the program. 16 Eco Rinse and Fast Rinse CANNOT be selected with Woollens, Bedding and Tub Cleaning program. Extra/Eco/Fast rinse is not designed to be used with fabric softener. Select Deep rinse if you are going to use fabric softener. NOTE: This option can change if machine is not starting, once the delay period is expire and machine start its normal operation, this option will disable. The estimate time is calculated automatically on the basis of the maximum recommended load for each type of fabric. After the program has started, the time remaining is updated every minute. End Of Program Start/Hold To Pause To start the selected program, press the "Start/Hold To Pause" button. If you have started your wash and you wish to stop it for some reason, press the "Start/Hold To Pause" button and hold it for 1. 2 second to enter PAUSE mode When the program is completed the 3 zeros will flash. Alarm Codes Display (Model: EWT704, EWT904) The display showns the following information: Machine In Pause Mode In the event of operating problems, some alarm codes can be displayed, for example (see "Troubleshooting" and "Troubleshooting fault displays" on page 26, 27, 28). [. . . ] Open lid, redistribute load, close lid Close lid Check drain hose for blockage Turn taps on Clean tap filters/washers Raise drain hose or fit a syphon break. Machine not working Water taps not turned on Out of balance switch off Lid not fully closed Communication error. Wiring is damaged. Machine has washed load but will not spin. Will not fill with water Water flowing out from washbowl indefinitely Out of balance Lid not fully closed E20 Drain hose blocked Water taps not turned on Inlet hoses blocked Drain hose too low Refer to installation instructions for correct positioning of hose. Make the machine level Adjust feet to touch the floor Redistribute clothes evenly Machine not level Machine goes out of balance or vibrates excessively when spinning Levelling feet not adjusted Clothes not evenly distributed Too much water for load size 26 Problem Display Code Possible Causes Loose inlet hose connections What to do Check connections at taps and rear of machine Use low water level Check detergent use and rewash clothes Remove some clothes and rewash Reselect program or temperature and rewash Use a higher water level If the item is visible, remove it with pliers. [. . . ]