User manual AEG-ELECTROLUX 32213G-TF-F

[. . . ] Please follow these simple precautions: The cleaner is double-insulated so it must not be earthed The cleaner is only to be used by adults. Young or infirm persons should be supervised to ensure they do not play with the appliance Always store in a dry place Do not use to pick up liquids Avoid sharp objects Do not pick up hot cinders or lighted cigarette ends Do not use near flammable gases Avoid tugging on the mains cable and check cable regularly for damage Note: Do not use cleaner with a damaged cable. If damaged the cable should be replaced at an Electrolux Service Centre The plug must be removed from the socket-outlet before cleaning or maintaining the appliance All service and repairs must be carried out by authorised Electrolux service staff Cable foot pedal HEPA filter indicator Standby/Overheat Indicator: Indicator will `illuminate' when cleaner is on standby, and `flash' if cleaner overheats Dust bag full indicator Cover release for dust bag/filter compartment Hose connection Power outlet (for the use of power driven tools) Back Saver® carrying handle Remote control handle On/off switch Temporary parking position for floor nozzle and tubes when in use Storage slot for floor nozzle and tubes when not in use Using Carpet/Hard floor nozzle Carpets: Use floor nozzle with lever in this position. Hard floors: Use floor nozzle with lever in this position. [. . . ] Precautions: Only use nozzle on carpets with a pile depth under 15 mm. Do not use on animal skins or rugs with long fringes. To avoid damaging your carpet, do not keep nozzle stationary whilst brush is rotating. Do not pass nozzle over mains cable and switch off nozzle immediately after use. Connect power nozzle plug to power outlet on cleaner and use clips to secure cable to tube and hose 5561. Power nozzle is activated by starting the cleaner 5561. Cleaning Power nozzle 5561 Disconnect from mains and remove entangled threads from nozzle by snipping threads with scissors. To clean wheels, gently lever them from their mountings. Dust bag indicator and changing the dust bag The dust bag should be changed when full. The dust bag indicator window will light up when full. If the dust bag should accidentally get broken in the cleaner, take cleaner to Electrolux Service Centre for cleaning. Water: If water is sucked into the cleaner the motor must be changed at an Electrolux Service Centre. NB Do not throw the batteries among other rubbish. Put them in a special recycling container. If you have any comments on the cleaner or the Instruction for Use Booklet please e-mail us on: floorcare@electrolux. Exist¤ un dispozitiv de siguran¤ care împiedic¤ închiderea capacului în cazul în care nu exist¤ o pung¤ de praf în¤untru. Before connecting the cleaner to an electrical supply ensure that the voltage marked on the data plate (on the underside of the cleaner) is correct for your electrical supply. If it is not, do not use the cleaner but refer back to your dealer. In the event of the fuse requiring replacement the fuse cover should be removed using a small screwdriver. The old fuse MUST be replaced by a 13A ASTA approved BS1362 fuse and the fuse cover must be replaced before the plug is used again. In the event of loss of the fuse cover, replacements can be obtained from your Electrolux dealer or Electricity Board and must be of the same colour as indicated by the coloured insert on the base of the plug. In no circumstances must the plug be used without a correct fuse cover fitted. [. . . ] The wires in the mains cable of this appliance are coloured in accordance with the following code: Blue: Neutral. As the colours of the wires in the mains cable of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. If using a three-pin plug, do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured green or green-and-yellow. [. . . ]