User manual AEG-ELECTROLUX 32514DG-W

[. . . ] Ensure that all control knobs are in the OFF position when not in use. Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric 21 cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. Child Safety This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. [. . . ] 3 Burner Big (rapid) Small (Auxiliary) minimum diameter 160 mm. 160 25 Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. Pan supports The pan supports are dishwasher proof. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. Ignition candle The electric ignition is obtained through a ceramic "candle" and a metal electrode (fig. 2-lett. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. 26 Something Not Working? F F . . . The gas ring burns unevenly -Check the main jet is not blocked and the burner crown is clear of food particles. -Check the burner cap and crown have been replaced correctly, e. g. . . . There is no spark when lighting the gas - Check that the unit is plugged in and the electrical supply is switched on - Check the mains fuse has not blown - Check the burner cap and crown have been replaced correctly, e. g. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Instruction for the Installer l l l l The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. The manufacturer will not accept liability, should any of the other safety instructions incorporated in this book or the regulation in force be ignored. 27 Technical Data Dimensions in mm: Overall dimensions H x W x D Cut out dimensions W x D Gas Burners Rating in Watt: Front auxiliary burner Back rapid burner Total burner rating in Watt Gas connection Setting Adjustments Category BE - FR IT - ES - PT - GR 8 x 290 x 510 270 x 490 1000 3000 4000 R 1/2 Natural gas - 20 mbar LPG 28-30/37 mbar II2E+3+ II2H3+ Injectors marks Burner Normal power kW Reduced power kW Nominal power Natural gas 20 mbar Injectors 100 mm Auxiliary Rapid 1 G20:3 G30:2, 8 0, 33 0, 65 70 119 m3/h 0, 095 0, 286 LPG 28-30/37 mbar Injectors 100 mm 50 86 g/h 72 202 28 Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut GJ 1/2". Interpose the sealing between the components as shown in fig. [. . . ] is fitted over the hob, the hanging furniture units beside the hood must be placed at 550 mm. minimum from the hob, to allow the fitting and the correct use of the lid, if required (fig. 12 a) Removable panel b) Space possibly useful for connections 80 Fig. 13 30 a b 20 min 380 140 FO 2166 Fig. [. . . ]