User manual AEG-ELECTROLUX 35771G-M

[. . . ] ENGLISH Important Safety Information BE These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. During Operation · · · · This appliance has been designed for non professional purpose in private houses only. It is meant to cook edible foodstuff only and MUST NOT be used for any other purposes. It is dangerous to alter the specification in any way. [. . . ] Then, check the flame is regular and adjust it as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Triple-crown Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 160 mm. mm. As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite If the control knobs become difficult to turn, please contact your local AEGElectrolux Service Force Centre. 61 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Pan Supports When washing the pan supports by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. The Burners The burner caps and crowns can be removed for cleaning. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. 62 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG-Electrolux Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. The gas ring burns unevenly If after all these checks, your hob still does not operate correctly, contact your local AEG-Electrolux Service Force Centre. 63 Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: 680 mm. 15 mm. CUT OUT DIMENSIONS Width: 560 mm. HEAT INPUT Central Burner (triple-crown) Rear Left Burner (rapid) Rear Right Burner (semi rapid) Front Right Burner (semi rapid) Front Left Burner (auxiliary) 4, 0 kW 2, 8 kW Natural Gas 2, 8 kW L. P. G. 2, 0 kW 2, 0 kW 1, 0 kW APPLIANCE CLASS APPLIANCE CATEGORY GAS SUPPLY 3 II2E+3+ Natural gas G20/G25 - 20/25mbar 64 BURNER NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS kW kW inj. m3/h G20 G25 20mbar 25mbar 0, 095 0, 111 LPG GAS 28-30/37 mbar g/h inj. [. . . ] between the switch contacts and of a type suitable for the required load in compliance with the current rules. The connection cable has to be placed in order that, in each part, it cannot reach a room temperature higher than 50 °C. The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase. REPLACEMENT OF THE VOLTAGE CABLE The replacement of the voltage cable requires the specific equipment of a technician. [. . . ]