User manual AEG-ELECTROLUX 35773G-M

[. . . ] When in use a gas cooking hob will produce heat and moisture in the room in which it 2 has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose. When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. [. . . ] This will allow the "thermocouple" to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Triple-crown Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 160 mm. 160 mm. As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite If the control knobs become difficult to turn, please contact your local AEG-Electrolux Service Force Centre. 7 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Pan Supports When washing the pan supports by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. The Burners The burner caps and crowns can be removed for cleaning. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. 8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG-Electrolux Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. after cleaning. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. If after all these checks, your hob still does not operate correctly, contact your local AEG-Electrolux Service Force Centre. 9 Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: Width: Depth: Thickness: 680 mm. 30 mm. CUT OUT DIMENSIONS HEAT INPUT Central Burner (triple-crown) Rear Left Burner (rapid) Rear Right Burner (semi rapid) Front Right Burner (semi rapid) Front Left Burner (auxiliary) 4, 0 kW 2, 8 kW Natural Gas G20 - 20 mbar 2, 8 kW L. P. G. G30/G31 28-30/37 mbar 2, 0 kW 2, 0 kW 1, 0 kW APPLIANCE CLASS APPLIANCE CATEGORY GAS SUPPLY 3 II2H3+ Natural gas G20 - 20 mbar 10 BURNER NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS 20 mbar kW kW inj. 1, 0 0, 33 70 m3/h G20 20mbar 0, 095 LPG GAS 28-30/37 mbar g/h inj. 1/100 50 G30 G31 73 71 2, 0 Natural Gas: 2, 8 LPG: 2, 8 4, 0 0, 45 96 0, 190 71 145 143 0, 65 113 0, 267 86 204 200 1, 2 146 0, 381 98 290 286 Burner Auxiliary Semi-rapid Rapid Triple-Crown Dia. Tap By-pass 1/100 mm 28 32 40 56 Aeration adjustment none 11 Installation The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. [. . . ] 12), and replace them with the ones required for the type of gas in use (see tables - pag. Reassemble the parts, following the same procedure backwards. Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply. You can find this label in the package of the injectors supplied with the appliance. FO 0392 · · Should the feeding gas pressure be different or variable compared with the required pressure, an appropriate pressure adjuster must be fitted on the gas supply pipe, in compliance with the rules in force. Fig. [. . . ]