User manual AEG-ELECTROLUX 5020B-MIL

[. . . ] 13 Charcoal filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Replacing the lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Special accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 7, Part1). 4 Electrical connection for the UK The appliance must be connected to fixed wiring with a double pole switched fused spur outlet with or without pilot lamp. We strongly recommend the appliance to be connected only by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology "DOUBLE POLE" means that both the live and the neutral supplies are switched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. IMPORTANT The wires of the mains lead supplied with this appliance are coloured in accordance with the following code: Blue-Neutral Brown-Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying the terminals in the plug, proceed as follows: The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. Appliances with 2 wires BLUE (NEUTRAL) BROWN (LIVE) LOAD L N LOAD L SUPPLY DP 13A, 250V FUSE ON N SUPPLY 5 Safety warnings for kitchen unit installer When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed. It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct. The air outlet installation must comply with the regulations laid down by the relevant authorities. d) Replace the grid. C C 4 10 The hood is fitted with one variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 5-15 minutes after having finished, thus ensuring that all that cooking odours are eliminated. Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. The risk of fat catching fire is increased when using dirty oil. It is extremely important to note that overheating can cause a fire. Never carry out any flambé cooking under the hood. Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). It is very important to clean the hood and the grease filters at the recommended intervals. Failure to do so could cause grease deposits to build up, causing a fire hazard. Safety warnings for user 11 Hood Operation Controls The hood is fitted with a variable speed motor. [. . . ] To remove rotate the filter in anticlockwise (Fig. Re-fit the metal filter 3 Attention Failure to observe the rules for cleaning the appliance and changing and cleaning the filters may cause fires. Therefore, we recommend you follow these instructions carefully. 14 Always turn off the electricity before replacing lamps!2) in order to check the lamps and replace them if necessary. Replacing the lamps A 2 A 2) Unscrew the lamps that do not work and replace them with 40W max lamps (E14). [. . . ]