User manual AEG-ELECTROLUX 6413K-MN87L

[. . . ] 6413K-MN Ceramic glass hob Table de cuisson vitrocéramique Glaskeramische kookplaat Installation and Operating Instructions Instructions de montage et mode d'emploi Montage- en gebruiksaanwijzing Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning!Information that affects your personal safety. Information that prevents damage to the appliance. [. . . ] Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 14 What to do if . . . Problem The cooking zones are not functioning. The cooking zones cannot be selected / Appliance does not react to the control panel input Possible cause No cooking zone selected Remedy Select cooking zone within 10 seconds of switching on (Decimal point lights up) More than 10 seconds have Switch on the appliance passed since the appliance again. was switched on Select cooking zone within 10 seconds of switching on The child safety device is activated l Deactivate the child safety device (See section "Child safety device") The sensor fields are partly Remove the cloth or the covered by a damp cloth or liquid with liquid Safety cut-out has been triggered Switch on the appliance again The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the therefore not hot Customer Service Department. Er03 Er21 Er25 is displayed Several sensor fields were touched at the same time Safety cut-out due to overheating Only touch one sensor field Let the appliance cool down. Disconnect the appliance from the electrical supply and have it connected properly Separate the appliance from the mains for a few minutes (remove the mains fuse). Let the appliance cool down. is displayed is displayed (only for 10 seconds) Appliance is incorrectly connected The overvoltage protector has been activated (for an incorrect connection see above Er25 or for overheating of the electronic components see Er21) Er40 is displayed 3 In the event of any other fault codes that arise, disconnect the appliance from the electrical supply for a few seconds. (Take out the fuse from the house's wiring system. ) If the fault is displayed again, please call the Customer Care Department and inform them of the fault code. 15 1 3 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance on the product or on its packaging indicates that this The symbol product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 2 W 16 Installation Instructions Safety instructions The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc. ) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. A protective floor must be installed under the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. Do not use silicon sealant between the appliance and the work top. Avoid installing the appliance next to doors and under windows. [. . . ] The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack of maintenance or failure to respect the assembly instructions or directions for use. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result from the addition of non-original accessories or spare parts are not covered by the guarantee. Appliances that are easy to transport may be delivered or sent to the consumer services department. [. . . ]