User manual AEG-ELECTROLUX 6530DG-M

[. . . ] Use this section until you are familiar with your new Hob. The section "Cleaning and Maintenance" provides information on both daily and more thorough cleaning of the individual components of the Hob. Should problems arise when you use the Hob, you can look in the section "Before calling service", where there are instructions on how to remedy some practical and technical problems yourself. Regards, 2 Table of contents Contents For the user Page no Your new aplliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is not designed for commercial/industrial purposes. Ensure that all the control knobs are in the OFF position when not in use. Do not use the gas hob if it is damaged in any way, contact your local AEG Service Centre. Disposal Make the gas hob unusable by cutting off the cable Dispose of any packaging material and old appliances at an authorised disposal sites. 4 The primary air intake aperture Must never be accidentally blocked by objects of any kind. 5 Description of the product Air intake Burner Control knob 6 Operations Burner markings Symbols at each control knob indicates which burner is adjusted with the control knob. Front Burner Back burner Panel markings Each control knob has a ring showing the scale of markings. Maximum flame Minimum flame 7 Burner ring/cover Together with the burner ring the burner ring/cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. If the burner ring/cover are wrongly placed the burner will operate incorrectly, and the burners may be damaged within at short space of time. Ignition electrode (A) Each burner has been provided with an ignition electrode. As long as the operating knob is depressed, the automatic ignition will ensure that a spark is emitted between the ignition electrode and the burner cover. Thermo Sensor (B) Ignition electrode (A) Thermo sensor (B) Burnerbody The hob unit features fully-secured gas taps (thermo-fuse) In case the flame goes out, the thermo sensor automatically prevents gas admission after a shorter time (max. Note: Gas admission is always allowed while the operation button is pressed See start-up procedure Burnercover 8 Ignition 1. Depress and turn the control knob for the burner to the left to max. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). The burner can now be regulated between maximum and minimum 9 Maintenance and cleaning For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Splashguard The splashguard can be removed to make it easier to clean the surface. Hold the splashguard as shown in the diagram. Clean the top surface as described in "cleaning the steel surface". Be aware of the two retaining pegs, which are sharp. Replace the splashguard in position ENSURE that it is fitted the correct way round. Never use hard or sharp implements to lift off the splashguard. Do not wash the splashguard in a dishwasher. [. . . ] The depth of the cut-out for any unit is: 490 mm Reinforcement Length of hole = sum of all units` externally measured length, less 20 mm. beams Mounting of Reinforcement Beams A reinforcement Beam, with supporting flanges at each end, is included with each two-burner unit. For unit combinations, a reinforcement beam must be used between each unit. 13 It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. Installation in work tops with a base unit underneath If the hob is to be installed on top of a base unit, a board must be mounted underneath the hob (e. g. [. . . ]