User manual AEG-ELECTROLUX 75852G-M

[. . . ] 75852 G Instruction Booklet Gas Hob GB IE 2 Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. [. . . ] If the burner accidentally goes out, turn the control knob to the "off" position (#) and wait for at least 1 minute before trying to light the burner again. Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table below). Burner Triple crown Large (rapid) Medium (semi-rapid) rear front Small (auxiliary) minimum diameter 180 mm 180 mm 120 mm 120 mm 80 mm maximum diameter 260 mm 260 mm 220 mm 180 mm 180 mm 9 As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. - For other hobs use Hob Brite or Bar Keepers Friend. Do not leave acid or alkaline substances (e. g. vinegar, salt, lemon juice, etc. ) on the cooktop. YES The Pan Supports The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. After cleaning, make sure that the pan supports are correctly positioned. To make burners work properly, ensure that pan supports are placed in a way that the arms are centred upon the burner as shown in the picture. Pay attention when replacing the pan supports in order to avoid damaging the hob top. NO 11 The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. The Ignition Electrode The electric ignition is obtained through a ceramic electrode which contains a metal electrode (Fig. Keep these components very clean, to avoid difficult lighting, and check that the burner crown holes (Fig. 1 - B) are not obstructed. 12 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM $ SOLUTION % There is no spark when lighting the gas. % % % Check that the unit is plugged in and the electrical supply is switched on. Check that the RCCB has not tripped (if fitted). Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. $ The gas ring burns unevenly. % % If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 13 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: 744 mm Depth: 510 mm Width: 560 mm Depth: 480 mm Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. [. . . ] The pressure reading should be nominally 20 mbar and must be between 17 mbar and 25 mbar. 4) Turn off the burner supplies. 27 Conversion from Natural Gas to Liquid Gas IMPORTANT The replacement/conversion from natural gas to liquid gas should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method ! 1) Ensure that the gas taps are in the 'OFF' position 2) Isolate the hob from the electricity supply 3) Remove all pan supports, burner caps, rings, crowns and control knobs. 4) With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors. TO ADJUST THE GAS RATE With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw. [. . . ]