User manual AEG-ELECTROLUX 76331K-MN 05S

[. . . ] To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. [. . . ] Control panel Display Touch Move your finger down from to se/, lect the desired heat setting between after 5 seconds . and As long as is displayed, the appliance works at full power. After the automatic warm up is completed, the heat setting / is displayed again. The length of time that the automatic warm up function operates depends on the heat setting selected. 12 Operating the appliance Heat setting 1 2 3 4 5 6 7 8 9 Length of the automatic warm up [min:sec] 1:00 1:40 2:40 4:50 5:30 6:30 8:10 10:10 12:20 2:30 2:30 3:30 4:30 --- 10 11 12 13 14 Operating the appliance 13 Using the child safety device The child safety device prevents unintentional use of the appliance. Switching on the child safety device Control panel 1. Touch for 4 seconds The child safety device is switched on. Step Display/Signal Overriding the child safety device The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards. Touch for 4 seconds lights up Until the appliance is next switched off, it can used as normal. Step 3 After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. Switching off the child safety device Control panel 1. The child safety device is switched off. Step Display/Signal lights up 14 Operating the appliance Using the timer Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use 3 3 If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. If a cooking zone is switched off, the timer function set is also switched off. Selecting a cooking zone Step 1. Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Removing deposits 1. Place a scraper on the glass ceramic surface at an angle. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolouration immediately yes yes ------when the appliance has cooled down ----yes yes yes cleaner for glass ceramic or stainless steel* using a scraper* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialized shops 3 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. What to do if . . . 21 What to do if . . . Problem Possible cause Remedy The cooking zones will not More than 10 seconds have Switch the appliance on again. switch on or are not function- passed since the appliance was ing switched on The child safety device is switched on Several sensor fields were touched at the same time Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field Automatic switch off has been Remove any objects (pan, triggered cloths, etc. ) that are lying on the control panel. Switch the appliance on again There is water on the control panel or the control panel is covered with fat splashes STOP+GO is activated Acoustic signal sounds when appliance is switched off The residual heat indicator is not displaying anything Acoustic signal sounds and appliance switches itself on and then off again; after 5 seconds another acoustic signal sounds lights up and number are displayed The control panel is wholly or partly covered by objects. [. . . ] Ensure anti-shock protection by installing correctly. The appliance must be connected to the electrical supply by a qualified electrician. Loose and inappropriate plug and socket connections can make the terminal overheat. Have the clamping connections correctly installed by a qualified electrician. [. . . ]