User manual AEG-ELECTROLUX 78001KF-MN 69F

[. . . ] 78001KF-MN Induktions-Glaskeramik-Kochfeld Ceramic glass induction hob Glaskeramische inductie-kookplaat Montage- und Gebrauchsanweisung Installation and Operating Instructions Montage- en gebruiksaanwijzing Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. The following symbols are used in the text: 1 3 2 Safety instructions Warning!Information that affects your personal safety. [. . . ] Sharp objects and abrasive cleaning materials will damage the appliance. Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Removing deposits 1. Place a scraper on the glass ceramic surface at an angle. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations imme- when the appliance has diately cooled down yes yes ----------yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 53 What to do if . . . Problem Possible cause Remedy The appliance cannot be More than 10 seconds have Switch the appliance on switched on or is not oper- passed since the appliance again. ating was switched on The lock is switched on l Switch off the lock (See the section "Locking/unlocking the control panel") Deactivate child safety device (See the section "Child safety device") Only touch one sensor field Remove any objects (pan, cloths, etc. ) that are lying on the control panel. Switch the appliance on again Switching off STOP+GO The child safety device is switched on l Several sensor fields were touched at the same time Safety cut-out has been triggered STOP+GO is activated u The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the therefore not hot Customer Service Department. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone h The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function Sensor fields are getting hot Cookware too big or placed Place cookware in the midtoo near the controls dle on one of the four cooking zoznes. Place large cookware on the back cooking zones in preference. Uncover sensor field Repeated acoustic signal One or more sensor fields (6x), appliance switches off have been covered for longer than 10 seconds Acoustic signal sounds The control panel is wholly Remove objects. when appliance is switched or partly covered by oboff jects. 54 Problem Possible cause Remedy Acoustic signal sounds and The On/Off sensor field has Do not place any objects appliance switches itself on been covered up, e. g. by a on the control panel and then off again; after 5 cloth seconds another acoustic signal sounds Display changes between two heat settings Power Management is reducing the power of this cooking zone Power Management is active, maximum load per side reached See the section " Switching the power function on and off" Use cooking zones on other side Use suitable cookware f flashes Unsuitable cookware No cookware on the cook- Put cookware on zone ing zone Diameter of the base of the Use suitable cookware cookware is too small for (min. 120 mm) the cooking zone Cookware not completely covering cross Place cookware centrally over the cross _ is lit Overheating protection for Switch off the cooking the cooking zone has been zone. Switch the cooking triggered zone on again Safety cut-out has been triggered Switch off the cooking zone. Switch the cooking zone on again Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department e and number are displayed Electronics fault If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 1 Warning!Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. 55 3 If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. [. . . ] 2 980 5276 Cyprus Hadjikyrlakos & Sons Ltd. Box 21587 Nicosia 1511 Service Telephones: Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Kuwait/Arabian Gulf Ali Al-Ghanim Est. Box 21540 - Safat Tel. : 4822190 Fax: 4820116 Lebanon Adib & Assaferi P. O. Box 539 Tripoli 61 Estonia Electrolux Estonia Ltd. [. . . ]