User manual AEG-ELECTROLUX 79301KF-MN

[. . . ] Useful tips and hints Environmental information 2 Contents Operating Instructions. Switching the STOP+GO function on and off. 4 4 6 6 6 7 7 8 8 8 8 9 9 10 11 12 15 16 16 16 17 Cleaning and care . 31 3 Operating Instructions 1 Safety instructions 3 5 Please comply with these instructions. [. . . ] Touch Control panel Switch on the appliance and Display/Signal l at the same time / acoustic signal Until the appliance is next switched off, it can used as normal. 3 After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. 11 Using the timer Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use 3 3 If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. If a cooking zone is switched off, the timer function set is also switched off. Selecting a cooking zone Step 1. Control panel Touch TIMER once Display Pilot light of the first cooking zone flashes Pilot light of the second cooking zone flashes Pilot light of the third cooking zone flashes Pilot light of the fourth cooking zone flashes 2. Touch TIMER once 3. Touch TIMER once 4. Touch TIMER once 3 3 12 If the pilot light is flashing more slowly, the heat setting can be set or modified. If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. Setting the time Step 1. Control panel Indicator Select TIMER cooking Pilot light for the cooking zone sezone lected flashes Touch or 00 to 99 minutes After a few seconds the pilot light flashes more slowly. The time counts down. Switching off the timer function Step 1. Control panel Indicator Select TIMER cooking Pilot light of cooking zone selected zone flashes faster Time remaining is displayed Touch The time remaining counts backwards to 00. 2. The pilot light goes out. The Timer function for the selected cooking zone is switched off. Changing the time Step 1. Wipe metal dcor strips with a damp cloth and a little washing up liquid. Soak dried on spillages with a wet cloth. Afterwards wipe off and rub dry. 19 What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have Switch the appliance on passed since the appliance again. was switched on The child safety device is switched on l Several sensor fields were touched at the same time Safety cut-out has been triggered Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field Remove any objects that are lying on the control panel. Switch the appliance on again Switching off STOP+GO STOP+GO is activated u Acoustic signal sounds The control panel is wholly Remove objects. when appliance is switched or partly covered by oboff jects. The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call your therefore not hot local Service Force Centre. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone h The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function 1. Set the cooking zone using the sensor field The heat setting was set using the sensor field Acoustic signal sounds and The On/Off sensor field has Do not place any objects appliance switches itself on been covered up, e. g. by a on the control panel and then off again; after 5 cloth seconds another acoustic signal sounds _ is lit Overheating protection for Switch off the cooking the cooking zone has been zone. Switch the cooking triggered zone on again 20 Problem e and number are displayed Possible cause Electronics fault Remedy Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department e and minus are displayed Light rays that are too Briefly shade the control strong on the control pan- panel, for example with el, for example bright sun- the hand Acoustic signal light sounds, appliance switches itself off Switch appliance on (again) 1 3 If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. [. . . ] The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. [. . . ]