User manual AEG-ELECTROLUX 8259D-M-CH

[. . . ] If the appliance has been equipped with a mains lead with a moulded-on type plug, the following regulations must be comply with: The plug moulded on to the lead incorporates a fuse. For replacement, use a 5 amp BS1362 fuse. Only ASTA approved or certified fuses should be used. If the fuse cover/carrier is lost, a replacement cover/carrie must be obtained from an electrical goods retailer. [. . . ] q If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr. - 610 899 004 (Ø 120 mm) which is one of our optional parts. q When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers gas cookers coal and oil cookers 600 mm 650 mm 700 mm min. q The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed. q It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct. The air outlet installation must comply with the regulations laid down by the relevant authorities. q When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. q National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room. q The national decree on fuel-burning systems specifies a maximum depression of 0. 04 bar in such rooms. 24 q Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm 2 large to avoid the possibility of a depression being created during operation of the hood. If you have any doubts, contact the relevant controlling authority or building inspectors office. q Since the rule for rooms with fuel burning appliances is outlet hole of the same size as the ventilation hole, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. q If the hood is used in its filtering function, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures. q When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation: short and straight outlet hose keep bends in outlet hose to a minimum never install the hoses with an acute angle, they must always follow a gentle curve only keep the hose as large as possible (120 mm Ø min. ). q Failure to observe these basic rules will drastically reduce the performance and increase the noise levels of the extractor hood. 25 Installation - Fig. 3 q Put the template onto the wall (1) and drill two Ø12mm holes (2). q Fit two hooks (3) on the drilled holes. q Hang the hood on the hooks and adjust the position of the hood using the two screws on the bottom of the hooks (5). q Remove the metal filters (4) and mark two points (6). Remove the hood and drill two Ø8mm holes on the marked points. Fit two Ø8mm wall dowels (7), Hang again the hood and fix the hood definitively with two screws 5X45 (8). q Fix the chimney support (10) with two screws 5 x 45 mm (9) and two wall dowels (11) on the wall close to the ceiling. q For exhausting version: Fit the connection ring (S) on the top of the hood with two screws Ø 3, 5 x 6, 5 mm (12S) then fit an axhausting pipe long enough to reach the outside (13S). For recycling version: Fix definitively the deflector (13K) on the top of the hood with two screws Ø 3, 5 x 6, 5 mm (12K). [. . . ] Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when it are dry. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur, this does not have any impact on its performance. q Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). 30 Carbon filter q The activated carbon filter should only be used if you want to use the hood in its filtering function. [. . . ]