User manual AEG-ELECTROLUX 825D-M

[. . . ] We strongly recommend the appliance to be connected only by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology "DOUBLE POLE" means that both the live and the neutral supplies are switched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. IMPORTANT The wires of the mains lead supplied with this appliance are coloured in accordance with the following code: Blue-Neutral Brown-Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying the terminals in the plug, proceed as follows: The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] q Hang the hood on the hooks and adjust the position of the hood using the two screws on the bottom of the hooks (5). q Remove the metal filters (4) and mark two points (6). Remove the hood and drill two Ø8mm holes on the marked points. Fit two Ø8mm wall dowels (7), Hang again the hood and fix the hood definitively with two screws 5X45 (8). q Fix the chimney support (10) with two screws 5 x 45 mm (9) and two wall dowels (11) on the wall close to the ceiling. q For exhausting version: Fit the connection ring (S) on the top of the hood with two screws Ø 3, 5 x 6, 5 mm (12S) then fit an exhausting pipe long enough to reach the outside (13S). For recycling version: Fix definitively the deflector (13K) on the top of the hood with two screws Ø 3, 5 x 6, 5 mm (12K). q Prepare the electric connection (14) (see relative chapter). q Fit the chimney (15) and fix it on the chimney support with two screws 3, 0 x 9 mm (16). The lower part of the chimney must be slided down and inserted on the housing on the upper part of the hood (18). q Fit the two grids (17) on both sides of the chimney. 9 Fig. 3 10 Hood Operation q The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The control switches are located on the unit's front panel: q the light switch switches the hood lamp on and off; q the motor switch switches the extractor motor on and off, enabling you to select one of the three different speeds. OI Light switch ON/OFF O123i Motor power adjustable to 3 positions O - OFF I - ON O - OFF I - LOW 2 - MEDIUM 3 - HIGH 11 Safety warnings for user q Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. q Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. q The risk of a fat fire increases when using dirty oil. q It is extremely important to note that overheating can cause a fire. q Never carry out any flambé cooking under the hood. q Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). q It is very important to clean the hood and replace the filter at the recommended intervals. Failure to do so could cause grease deposits to build up, causing a fire hazard. 12 Maintenance and care q The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter q The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in extraction or recirculation mode. [. . . ] q Replace the old light bulb with a new light bulb (40 W max. ). q If the light does not come on, make sure the bulb has been screwed in correctly before contacting AEG Service Force. . Fig. 6 15 Cleaning q Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor's protective grid. [. . . ]