User manual AEG-ELECTROLUX 86700K-MNHIC80

[. . . ] To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device. General safety The appliance may only be installed and connected by trained, registered service engineers. Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards. In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock. Repairs to the appliance must only be carried out by trained registered service engineers. [. . . ] Control panel Switch on Switch off Touch Touch Display l (for 5 seconds) previously set heat setting 3 10 When you switch the appliance off, the locking function is automatically switched off. Using the automatic warm-up function All cooking zones are equpped with an automatic warm up function When setting a heat setting using , when starting from , the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set. Control panel Switch on Touch (only when starting at possible heat settings Display to ) a (after 5 seconds) Switch off Not used Touch Touch to / u to u to u to u 3 3 If during the automatic warm up a a higher heat setting is selected, e. g. from to , the automatic warm up is adjusted. If there is still residual heat on the cooking zone (display h), the automatic warm up is not performed. The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting v 1 2 3 4 5 6 7 8 9 Length of the automatic warm up [min:sec] 0:30 1:00 1:40 4:50 6:30 10:10 2:00 3:30 4:30 --- Intermedi- Length of the ate heat automatic warm up setting [min:sec] 2. 6. 2:40 5:30 8:10 12:20 2:30 11 Using the child safety device The child safety device prevents unintentional use of the appliance. Setting the child safety device Step 1. Control panel Switch on the appliance (Do not set a heat setting) Touch Touch Display/Signal until the signal sounds Acoustic signal l Appliance switches off. The child safety device is engaged. Releasing the child safety device Step 1. Touch Touch Control panel Switch on the appliance Display/Signal l until the signal sounds Acoustic signal Appliance switches off. The child safety device is released. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Place a scraper on the glass ceramic surface at an angle. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations imme- when the appliance has diately cooled down yes yes ----------yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 19 What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have Switch the appliance on passed since the appliance again. was switched on The child safety device is switched on l Several sensor fields were touched at the same time Safety cut-out has been triggered Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field Remove any objects that are lying on the control panel. Switch the appliance on again Switch off the lock (See the section "Locking/unlocking the control panel") The lock is switched on l Acoustic signal sounds The control panel is wholly Remove objects. when appliance is switched or partly covered by oboff jects. The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the therefore not hot Customer Service Department. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone h The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function 1. Set the cooking zone using the sensor field The heat setting was set using the sensor field Acoustic signal sounds and The On/Off sensor field has Do not place any objects appliance switches itself on been covered up, e. g. [. . . ] Loose and inappropriate plug and socket connections can make the terminal overheat. Have the clamping joints correctedly installed by a qualified electrician. In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90 (or higher) must be used. If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90; or higher). [. . . ]