User manual AEG-ELECTROLUX 88001K-IN 97U

[. . . ] And please pass it to any future owner of the appliance. We wish you much joy with your new appliance. Contents Operating Instructions Safety information Description of the appliance Operating the appliance Tips on cooking and frying Cleaning and care 2 2 4 6 11 13 What to do if . . . Disposal Installation Instructions Safety information Service Warranty 14 16 16 16 18 19 Subject to change without notice Operating Instructions Safety information WARNING!If you do not, any damage resulting is not covered by the warranty. [. . . ] Example: the heat setting 14 is selected on one cooking zone. The power function is switched on for the corresponding cooking zone. The power function is carried out but the heat setting 14 of one of the cooking zones and the power function for the other cooking zone of the pair exceed the maximum power for both at the same time. For this purpose, the power management reduces the power of the cooking zone that switched on first from 14 to example 5 and the display of this cooking zone changes between 14 and 5 and then stays at the current possible maximum 5 (If the display changes between 14 and 5 or 14 and 3 or another value depends on the type of appliance and the size of the cooking zone). Using the timer Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use If just one countdown value is set you can change it only when the appliance is switched on. If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. If a cooking zone is switched off, the timer function set is also switched off. Control panel Touch once Display Pilot light of the first cooking zone flashes 10 Operating the appliance Step 2. Control panel Touch Touch Touch once once once Display Pilot light of the second cooking zone flashes Pilot light of the third cooking zone flashes Pilot light of the fourth cooking zone flashes If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. Control panel Select a cooking zone Touch or Display Pilot light for the cooking zone selected flashes 00 to 99 minutes After a few seconds the pilot light flashes more slowly. The time counts down. Switching off the timer function Step 1. Control panel Select a cooking zone Touch Display Pilot light of cooking zone selected flashes faster Time remaining is displayed The time remaining counts backwards to 00 . The pilot light goes out. Cleaning the appliance after each use 1. Food containing sugar, plastics, tin foil residues should be removed at once using a scraper. Place a scraper on the glass ceramic surface at an angle and remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Finally, rub the appliance dry using a clean cloth . Limescale rings, water rings, fat splashes, shiny metallic discolorations should be removed after the appliance has cooled down using cleaner for glass ceramic or stainless steel. What to do if . . . Problem/Display Possible Cause Remedy The cooking zones cannot be More than 10 seconds have Switch the appliance on again. switched on or are not operat- passed since the appliance was ing switched on The lock is switched on Switch off the lock (See the section "Locking/unlocking the control panel") Deactivate child safety device (see the section "Child safety device") Only touch one sensor field The child safety device is switched on Several sensor fields were touched at the same time Automatic switch-off has been Remove any objects (pans, etc. ) triggered that are lying on the control panel. Switch appliance on again There is water on the control panel or the control panel is covered with fat splashes STOP+GO is activated Display is switching between two heat settings The residual heat indicator is not displaying anything lights up Power management is reducing the power of this cooking zone Wipe the control panel Switch off STOP+GO See the section "Switching the power function on and off" The cooking zone was only on If the cooking zone is supposed for a short time and is therefore to be hot, call your local Service not hot Force Centre. Unsuitable cookware No cookware on the cooking zone Diameter of the base of the cookware is too small for the cooking zone Use suitable cookware Put cookware on zone Move to smaller cooking zone Use suitable cookware What to do if . . . Problem/Display lights up and number are displayed Possible Cause Remedy 15 Automatic switch-off has been Switch appliance off. Switch triggered appliance on again Electronics fault Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, is displayed again, call the customer service department Remove objects. Acoustic signal sounds when appliance is switched off Repeated acoustic signal (6x), appliance switches off The control panel is wholly or partly covered by objects. One or more sensor fields have Uncover sensor field been covered for longer than 10 seconds Acoustic signal sounds and ap- The On/Off sensor field has Do not place any objects on the pliance switches itself on and been covered up, e. g. by a cloth control panel then off again; after 5 seconds another acoustic signal sounds If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. [. . . ] 5 Rating Plate 88001K-IN 97U 55 GBD C1 AU AEG-ELECTROLUX 949 592 863 Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section "What to do if. . . "). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: Warranty ­ Three-digit-letter combination for glass ceramic ­ Model description ­ Product number (PNC) ­ Serial number (S No. - see the rating plate) ­ Type of fault ­ Any error messages displayed by the appliance 19 Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND This document sets out the terms and conditions of product warranties for Electrolux branded appliances. [. . . ]