User manual AEG-ELECTROLUX 88101K-MN 84F

[. . . ] 88101K Ceramic glass induction hob Table de cuisson vetrocramique induction Glaskeramische inductie-kookplaat Installation and Operating Instructions Instructions de montage et mode d'emploi Montage- en gebruiksaanwijzing Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning!Information that affects your personal safety. Information that prevents damage to the appliance. [. . . ] Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations imme- when the appliance has diately cooled down yes yes ----------yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 21 What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have Switch the appliance on passed since the appliance again. was switched on The lock is switched on l Switch off the lock (See the section "Locking/unlocking the control panel") Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field The child safety device is switched on l Several sensor fields were touched at the same time The sensor fields are partly Remove the cloth or the covered by a damp cloth or liquid. with liquid Switch the appliance on again. Safety cut-out has been triggered STOP+GO is activated Switch the appliance on again Switching off STOP+GO The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the therefore not hot Customer Service Department. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone h The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function Uncover sensor field Repeated acoustic signal One or more sensor fields (6x), appliance switches off have been covered for longer than 10 seconds Acoustic signal sounds and The On/Off sensor field has Do not place any objects appliance switches itself on been covered up, e. g. by a on the control panel and then off again; after 5 cloth seconds another acoustic signal sounds Display is switching between two heat settings Power management is reducing the power of this cooking zone See the section "Switching the power function on and off" 22 Problem Possible cause Unsuitable cookware No cookware on the cooking zone Remedy Use suitable cookware Place cookware on the cooking zone f flashes The diameter of the botMove onto a smaller cooktom of the cookware is too ing zone small for the cooking zone Use suitable cookware _ is lit e and number are displayed Overheating protection for Switch off the cooking the cooking zone has been zone. Switch the cooking triggered zone on again Electronics fault Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department 1 3 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. 23 Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance 2 The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. W 24 Installation Instructions Safety instructions The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc. ) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances are to be observed. Drawers may only be installed with a with protective board directly under the appliance. The cut surfaces of the work top are to be protected against moisture using a suitable sealant. [. . . ] Box 21587 Nicosia 1511 Service Telephones: Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Kuwait/Arabian Gulf Ali Al-Ghanim Est. Box 21540 - Safat Tel. : 4822190 Fax: 4820116 Lebanon Adib & Assaferi P. O. Box 539 Tripoli 29 Estonia Electrolux Estonia Ltd. Mustame tee 24 EE0006 Tallinn Tel. : (372) 6 650 090 Fax: (372) 6 650 092 Hong Kong Dah Chong Hong Ltd. [. . . ]